direct mount chain guide 3d models

SummaryThis cable guide secures your wires on your Microswiss Direct Drive. There's also a cable guide for the X Gantry (where the original extruder went). These ensure that your wiring doesn't get damaged from movement.This should be compatible with...

As a significant enhancement to the direct drive extruder conversion from Tech-tweak, available on Thingiverse at https://www.thingiverse.com/thing:4313820, this filament guide effectively links the runout sensor located at the rear of the Jgaurora...

A redesigned version of the Dual Gear Direct Drive Extruder Mount that includes a hookup for a cable chain. I also trimmed a bit of material from the floor of it to more easily be able to access the tension screw for the extruder assembly. Very clean...

This is a filament guide designed specifically for the ender3 direct drive converted machine, making it extremely easy to print with PLA, ABS, and PETG materials. A secure fastening method is required to keep the guide firmly in place, and this can...

I wanted to take a stab at designing a filament guide that was print-in-place, but had a dynamic swivel component. Hole in the swivel is designed to accept a small length of PTFE tube at the top. It's intentionally tight to get a good friction fit....

Filament guide designed for mounting on 2020 aluminum extrusion using an M5x10 bolt and T-nut. A lip is present at the bottom, allowing a few degrees of adjustment without being too tight in the groove. It utilizes a bowden adapter from the titan...

I recently installed a direct extruder upgrade on my printer and discovered that I needed a new filament guide to keep the material vertical and prevent snags on the frame, so I designed this one. Hopefully, it will be useful for someone else too. ...

I made this desgin to turn around the cable chain after doing the direct drive modification. ... <i><b>You need:</i></b> - 4x M3 Nut - 4x M3x6 Screw <i><b>Print settings:</b></i> Resolution: 0.2mm Infill: 100% Rafts: no Material: PLA...

... the structure rigidity. - Added drag chain mount with cable management. ... All parts to be printed without support Parts list: - M3 heatset nut X6 - M3 bolt - M3 sprint washer X2 - Small cable ties X2 https://youtu.be/3tfYWGdNnio

I went with a 4 wheel carriage for my ender 3 pros direct drive conversion. It is a little wider than the OEM 3 wheel plate. So I remixed another mount. I had to make it a little wider and then I reinforced it in 3 areas a little more. I printed it...

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655) This version has a 9mm Y offset to be compatible with HeroMe Gen 5

However, I chose not to modify this section further to avoid covering the wire hole on the upper-right portion of the BMG backplate or misaligning the mount from the other Z-stepper mounted side. A small divot was added to one side of the mount,...

I wanted to reposition to make room for the direct drive in the event I print as high as possible. ...

use any print settings then mount to 2040 extrusion with t slots

Ender 5, Ender 5 Plus, etc. ... Microswiss direct drive chain bracket for the Bretware chain systems.

... carriage and the old extruder mount on the side. I have found it works pretty well! For this you are going to need: -4 m3x12 screws for the Side Mount -2 m3x8 screw for extruder mount I printed off 15 Chains for the X axis and 18 for the y axis

Remix a snug fit gantry mount for Ender 3 Neo / S1, no additional tool needed. You can use a piece of double side tape on the left inside to make it more stable. ... Also add a right side carriage mount for my Briss fang.

If you've got your 3D printer with a bed chain mounted on a tale, this setup is perfect for you! ...This guide shows you how to attach the cable chain directly onto the table, securing it tightly in place with screws.

Chain guide for xr250/ Tornado

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3t4EtFPnat9

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3t4EtFPnat9

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3t4EtFPnat9

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3t4EtFPnat9

Cable channel bracing for Direct drive by Anksunamun bracing.stl - 1 chain_start_frame.stl - 1 chain_clip.stl - 18 chain_link_last.stl - 1 chain_link.stl - 16

Quick Remix of Madau3D's Direct Drivinator. ...Adds a bracket for a cable chain attachment.

chain guide for kmx and kdx

chain guide anti derailleur type mrp high

Eccentric drive chain guide with parasitic sprocket

Wanted a simple adapter to get my cable chain to work with my printer, using Klinger's version as a base I extended it a bit to get a slighter stronger mount and gave added extra mounting points for the cable chain. You should be able to fit 3 chains...

I have found it works pretty well! For this you are going to need: -4 m3x12 screws for the Side Mount -2 m3x8 screw for extruder mount I printed off 15 Chains for the X axis and 18 for the y axis Print Settings Printer Brand: Creality Printer: Ender...