direct mount chain guide 3d models

This is an anchor point for a series of cables sourced directly from Amazon via the unique product identifier B00AUB24VC.

... masterpiece. ...The remix of thing 3190998 and thing 2896612 is a true innovation. To bring this concept to life, print it on the flat side for maximum stability. This creation relies heavily on the ingenious chain design found in thing 2920060.

Wanted to use this system on my son's Aquila so I just remixed the extruder mount by PenitentHollow to fit the slightly different metal plate that holds the extruder and z-axis rod. ... The bottom connector by Ilueen...

Wanted to use this system on my son's Aquila so I just remixed the extruder mount by PenitentHollow to fit the slightly different metal plate that holds the extruder and z-axis rod. ... The bottom connector by Ilueen...

... as much as I'm satisfied with it for now. There's room for tweaks here and there, but as it stands, it works great with minimal post-print processing. If you do decide to print this, consider using at least 70% infill, especially on the mounts!

... for now, though it could use some fine-tuning here and there. Nonetheless, as it stands, it works beautifully after minimal post-print processing. If you do decide to print, make sure to use at least 70% infill – the mounts in particular require it.

Direct Drive filament guide and run-out sensor mount for Ender3/V2 and others. ... Allows for side mounted spool holder Updated design with Left or Right uprights with holes and nut pocket inserted to eliminate the need to drill for them.

Chain mounts and bl touch mount for ender 5 plus + microswiss direct drive After adding the Hero Me Gen5 to my ender 5 plus I didn't have a bracket that fit my bl touch and I wanted cable chains so I made mounts for them.

This is a filament runout sensor mount for the CR10S-S5 with a direct drive extruder. Fits in at the old bowden motor mount with the stock screws and 3 M3 nuts. I made this to use the 3mm threaded heat inserts rather than thread directly into...

Sapphire Plus Pack Mod (Direct +Volcano E3D V6 + Cable Chain Mount) Installation is performed on a standard belt tensioner mount. All elements are universal and interchangeable. ...

Make Z/X chain mount for Direct Drive on my ENDER 3 V2 Use this chain https://www.thingiverse.com/thing:3715002 Make inside corner of Z mount slightly rounder, for safety of wires. ... Use 3 x M3 screw.

The two original bolts that mounted the drag chain to the stock location can be used to bolt up my mount in place. The other drag chain mount gets bolted into the old stepper motor mount location on the right side of the frame. ...4x M4 x8mm bolts and...

I knocked together a silly filament guide that mounts to the NEMA17 (31x31) plate where the extruder motor used to be on my Ender 3 V2. This is for use with an Ender 3 that no longer has the extruder stepper motor attached to the frame. I recently...

I knocked together a silly filament guide that mounts to the NEMA17 (31x31) plate where the extruder motor used to be on my Ender 3 V2. This is for use with an Ender 3 that no longer has the extruder stepper motor attached to the frame. I recently...

... able to find one made me decide to make this little peg. You can hand thread a PC4-M6 fitting in the hole and use your left over bowden tube to guide the filament from the bottom. ... Seeing as this is a structural part print with 100% infill

This is a filament guide to mount on a roof of an enclosure, it is meant for direct drives where u have no space of mounting the spool on top but from the side. I used 2x metal u-grooved filament guidewheels with some M4 bolts. ...

Two Tress Sapphire Pro Orbiter direct drive mount adapter with cable chain.2021/12/31 - add orbiter_adapter_v2 - high versionRemix:orbiter adapter: https://www.thingiverse.com/thing:4763280cable chain: https://www.thingiverse.com/thing:1915486 

For the Titan direct mount X axis cable drag chain adaption, check out the designs on Thingiverse: https://www.thingiverse.com/thing:3751041 and compare them to the original one. To adapt it, you won't need a new base; just drill a 3.5 mm hole. ...PETG...

Patreon - https://patreon.com/CosmicNimbusPrintingGumroad - https://cosmicnimbus.gumroad.com Hey fellow Ender 3 v2 Neo user ! I've been looking for a working cable chain setup for my E3v2Neo that also allows for the Direct Drive Extrusion mount on...

Here is the 10x20mm Cable Chain I used, https://a.co/d/iSzwFDn There are little rectangular stoppers on the inside of the hole sections on each link to stop the cable from rotating 180° so on the pinned mounting brackets you print, you will have to...

Just my design of a Cable guide for CR10, after upgrading to direct drive extruder Super Simple.

Made a nicer looking filament guide for direct drive! ...it is just slide in and no need for screws.

Direct Drive Filament Guide Mod - low profile and less filament For use with Spool Holder for Ender 3 (by rnelias)

I wanted to take a stab at designing a filament guide that was print-in-place, but had a dynamic swivel component. Hole in the swivel is designed to accept a small length of PTFE tube at the top. It's intentionally tight to get a good friction...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive.thIt is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002and some Nema17 motor chain mount I...

It is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002 and some Nema17 motor chain mount I found a couple of years ago and can no longer identify the source or the author. There are two versions of...

The Fanduct ist a Remix of this Thing: https://www.thingiverse.com/thing:2759439/remixes The mounts optimized to use it with cheap direct extruder mod for Ender. take a look at the photos before start printing, it need some parts more to DIY. ... Be...

I remixed the excellent Ender 3v2 direct drive adapter by Peviox (https://www.thingiverse.com/thing:5216067) with enough clearance for a 20mm fan on top of the Briss Moto duct and added a mount for the slim cable chain by norp...

I remixed the excellent Ender 3v2 direct drive adapter by Peviox (https://www.thingiverse.com/thing:5216067) with enough clearance for a 20mm fan on top of the Briss Moto duct and added a mount for the slim cable chain by norp...

... slides over the extruder motor without requiring any additional hardware. For a reliable chain system, visit: https://www.thingiverse.com/thing:2920060 If you're using a direct drive like I am, check out: https://www.thingiverse.com/thing:3386628