direct mount chain guide 3d models

The revised chain guide is designed for use in 1x10, 1x9 mountain bike drivetrains with direct mount bosses. The updated design features smoothed inner walls, preventing chain snagging on sharp edges. ...With a two-part system that has been greatly...

Here are spacers designed specifically for mounting. You can find them on Thingiverse at this link: https://www.thingiverse.com/thing:2504355. ...These spacers come in various sizes, ranging from 1.5mm to 5mm.

Hi!I am ex pro cyclist. ...I spend a lot of time designing and testing chain guides. This model is fully adjustable and fits all bikes with high direct front derailleur mount. I have tested it during 2 seasons of racing. ... Ultra light- 18g!

Hi!I am ex pro cyclist. ...I spend a lot of time designing and testing chain guides. This model is fully adjustable and fits all bikes with high direct front derailleur mount. I have tested it during 2 seasons of racing. ... Ultra light- 18g!

Utilized on a Haibike Nduro Sduro RX 2016 bike, this component is employed with a solitary 32-tooth chainring.

I spend a lot of time designing and testing chain guides. This model is fully adjustable and fits all bikes with e type front derailleur mount. I have tested it during 2 seasons of racing. ... PLA is strong enought when you print it in good...

Hi!I am ex pro cyclist. ...I spend a lot of time designing and testing chain guides. This model is fully adjustable and fits all bikes with e type front derailleur mount. ...I have tested it during 2 seasons of racing.

I'm building a custom mount for my recumbent bike's chain guide tubes. ...This is my inaugural project with Fusion 360, and I'm excited to put this software to the test.

I basically just removed the small filament guide from the original design and attached the guide from this thing: https://www.thingiverse.com/thing:3643366 Thanks for both awesome designs!

I completely revamped the tiny filament guide by stripping it from the initial blueprint and seamlessly integrating the sleek guide from this impressive creation: https://www.thingiverse.com/thing:3643366 I'm extremely grateful for both innovative...

Quick-Attach Direct Drive Filler Guide Mounts Securely to Top Printer Rail

I needed a filament guide for my Ender 3 (which is converted to direct drive) BUT I didn't want one that mounted parallel to the bed since that can impact print height. I liked the simplicity of the original guide, but wanted it mounted on the top,...

Cable chain mount for microswiss direct drive on the ender 5. You can use these clips for the cable guides or just use zip ties. ... https://www.thingiverse.com/thing:4936515

It is directly mounted on E-axis with the upper two M4 screws of X-axis bearing bushing. As the endstop swich has very small roller, I used grooved pulley (13 mm outer diameter, 2 mm groove) as interface part. If you have the original board,...

Set the guide cable chains for direct extruder in Tevo Flash immediately. Be sure to consult the detailed instructions on Thingiverse at https://www.thingiverse.com/thing:3480386 before updating the guide chain. ...If you need further clarification or...

Thanks for the design! ... I made a new chain mounting point for the cheapo direct drive kit on bangood. ...It mounts in the 2 M3 screw holes that support the extruder mechanism

I do construct this filament sensor and chain guide support to use with Hemera Mount from https://www.thingiverse.com/thing:5335008 Hope it will be usefull for you!

I liked the chains that had the little clip and other adapter parts, but I needed a mount to go on my direct drive extruder, so this is what I whipped up. I'm still working on an adapter plate that will take a bearing or something that can be...

... after it was installed. I used the rear gantry cable chain connector from here: https://www.thingiverse.com/thing:3274980 I also remixed the chain links to fit together better with less chance of snapping: https://www.thingiverse.com/thing:4742487

I had purchased a metal direct drive adapter (https://www.amazon.com/dp/B09KG8MMQ2?psc=1&ref=ppx_yo2ov_dt_b_product_details) for my Ender 3 Pro. I had printed one, but it was getting loose. I printed out the Cable Chain setup but needed a way to...

# Installation To install this addon, simply reverse the direction of both end chain links. # Features Cables experience less stress due to an improved bend radius. The chainguide runs on the backside, giving you space to work and keeping it out of...

motorcycle chain guide

This is a direct drive spool mount Bowden guide for my system.

Le projet originel de FedorSosnin est accessible à cette adresse https://www.thingiverse.com/thing:3643366 Le projet originel de K Sims est accessible à cette adresse https://www.thingiverse.com/thing:3561563 ---------------- [English] Mixing of the...

It uses the old location of the extruder stepper motor to mount a filament guide which swivels on it's own as the extruder moves. The "post" slides under the "base" and, and then gets mounted to the old extruder servo mount with M3 nuts and bolts. ...

It's best to orient your prints at a deliberate angle to prevent layer lines from coinciding perfectly with the chains.

extended the cable chain mount out so it sits passed the direct drive mount. ... Remixed from: https://www.thingiverse.com/thing:4314829

Used meshmixer to cut a loading slot into the filament guide by TheLizard - https://www.thingiverse.com/thing:4729328 For those as lazy as me to not want to unload-reload filament just to start using the new guide :) Slot positioning works for me,...

Used meshmixer to cut a loading slot into the filament guide by TheLizard - https://www.thingiverse.com/thing:4729328 For those as lazy as me to not want to unload-reload filament just to start using the new guide :) Slot positioning works for me,...

A couple of frame mount parts remixed from originals. ... This allows for a vertical mount of the cable chain to the print head of the TronXY Direct Drive kit.