direct drive extruder 3d models

Direct drive for tevo little monster - Lightweight compact and high pushing force - Print the case in Nylon or PC-ABS the LDO motor heat-up to 75°C Parts need: - BGM drive...

So away to TinkerCAD I went and designed this to fit atop and between the Extruder and the Y Axis Carriage for the direct drive assembly. It is designed so that the neck of the Y Adapter will fit in support and you can place a ziptie through the...

I've searched a lot for upgrading my old extruder to a direct drive one. I've found lots of nice designs on this website but I wanted to design my own with the following targets : Using only parts I had in my spare parts Fits Prusa i3 Rework style...

I've spent countless hours searching for ways to upgrade my old extruder to a direct drive one. I've scoured this website for inspiration and found numerous designs that sparked my interest. However, I wanted to create my own design with specific...

This is my design for my anycubic kobra go printer because I wanted to convert it to a direct drive drive.It is easier to mount because you just have to slide the other to the roller

8, 2021 (see Change Log section near the bottom of this post) ## A Simple, Lightweight Direct Drive Mount for BMG Extruders and V6 Hotends This is a compact and easy-to-print direct drive mount compatible with open carriage printers such as Ender 3...

#MJØLNIR LWX 31 | 155 gram | Direct Drive | Dual Gear | Light Weight eXtruder Mjølnir NEMA 14 motor: https://s.click.aliexpress.com/e/_9jtVG0 Mjølnir Gear set: https://s.click.aliexpress.com/e/_9jXj9w How to assemble: https://youtu.be/Zbhv6hjX4qc...

Wanted to couple the ABL system with that specific extruder by fashioning a customized attachment linking the servo mount directly to the hotend clamp's anchor points.

This is a direct drive adapter bracket for the stock Creality Ender 3. You can reuse the original extruder motor and parts cooling fan and duct with this bracket, so you'll only need to buy the Titan extruder, V6 hotend, and inductive sensor. I use...

The motor, drive gear, tension spring and filament roller can be used from your existing extruder or purchased separately. It is designed to fit a knock off V6 hot end but should fit the genuine one in theory, you can either use the stock V6 cooling...

2019/11/23: * I added a new cam lock for the breech that allows more direct and even pressure on the filament without bottoming out against the case. * I included new upper and lower cases for internal bearing tolerances/alignment and the new cam...

resized the knob end to be smaller to accommodate the smaller space with the direct drive setup. the shaft hole was left unchanged but didnt fit without filing etc. the hole was to small. Palodion... ...thanks for the design.

This is an 18mm sensor adapter tailored specifically for the direct drive carriage, a precise replica of Prusa's design, engineered to seamlessly integrate with Anet A8 and similar printers.

Instead of getting a direct extruder as planned, I received one designed for a bowden system. Fortunately, I still had some spare PC4-M6 bowden couplers and M6 nuts on hand, which allowed me to create an adapter to solve my problem. ... I hope this...

It is simply another extruder that pays homage to many treasured extruders found on Thingiverse. This particular model is designed specifically for the MK7 drive gear and 1.75mm filament. Bearing selection involves using a high-quality 696zz bearing,...

For optimal results, use the file named CE3_direct_drive_v1.1.stl. Initially, I printed the original model, but it had a major flaw - part of the design was in contact with one of the wheels on the x-axis and my pc4-m6 coupler was too long. To...

The idler used to fail to reach the drive gear as intended; I had to trim some material off it to achieve this now. ... As of right now, I think these updates are final but there could be additional modifications down the line that escape my memory for...

I don't know for sure but I suspect this fits most Micro Swiss extruders, at least those with the 8mm drive gear. Prints without supports, low infill (20% or so) seems fine. Combined with my Filament Runout Sensor upgrade (link below), this...

A mounting bracket for converting A20 bowden extrusion to direct extrusion, with stock extruder, filament detector and stepper motor reused. Need 4 countersink M3 screws, a short piece of Teflon tube. Based on the dimension of G_Goro's design,...

As I use Sapphire pro printer, I've used all parts from it dual drive bowden extruder. Main gear shaft on my extruder is 29mm, as original design can accept only 28mm shaft, I adapted my design for 29mm shaft. I'm sure that it will work for 28mm as...

Other parts are specifically designed for direct drive with adjustable tension, a remix of http://www.thingiverse.com/thing:53125. To complete the set, you'll need to print the rest of the parts from Satoer's original design and optionally some...

Other parts are for the direct drive (remix of http://www.thingiverse.com/thing:53125) with adjustable tension. For complete set you need to print the rest of the parts from Satoer's original design and optionally some parts from LuisCruz's remix...

This modification makes direct drive easier to implement. The current version is DEPRECATED; I suggest using the new update instead. Updates include: 01-10-2016 - A new version can be found at http://www.thingiverse.com/thing:1257733. ... Printer...

Direct drive reusing the stock fan shroud. Wire bracket: https://www.thingiverse.com/thing:4559502 This was designed with no supports in mind, the zip tie slot is 4x2.5mm you should be able to bridge that. Hardware List! Motor bracket: ...

to remove vertical wiggling during retraction moves i modified mikelanes design so you can use the x-axis roller/carriage bolts to fasten the direct drive conversion mount instead. furthermore i aligned the preexisting slots with the openings on the...

Installs on the extruder stepper shaft with a small magnet.

The choice of parts was quite deliberate: an MK7 drive gear for the filament, used in reverse compared to the Creatr Leapfrog extruder instructions; a 624zz bearing, carefully mounted between two M4 washers to create a sturdy idler assembly; and of...

Dual Metal Gear (NOT BMG) Direct drive reusing the stock fan shroud. Wire bracket: https://www.thingiverse.com/thing:4559502 This was designed with no supports in mind, the zip tie slot is 4x2.5mm you should be able to bridge that. Hardware...

Direct drive reusing all stock parts (fan shroud!!!). Wire bracket: https://www.thingiverse.com/thing:4559502 This was designed with no supports in mind, the zip tie slot is 4x2.5mm you should be able to bridge that. Hardware List! Motor...

This model can also be used with a standard aluminum extruder, but you'll need to adjust the spacer thickness to fit your needs. Heat set inserts (M3-0.5mm) are utilized in this design, which can be found on eBay or Amazon at an affordable price. The...