direct drive ender 3 3d models

I originally tried the [Ender 3 Direct Drive Linear X-Axis Mount by vnomus427](https://www.thingiverse.com/thing:4433174) but I found that my direct drive wasn't the same size as the one that mount was for - I have a couple of centimeters of Bowden...

The stock Ender 3 Limit Switch doesn't have a LED so I grabbed one that I had laying around and soldered it to the limit switch (along with its resistor). The screws are nylon M3 with nylon nuts... I bought a bunch of them 15mm to 20mm then just...

I added a Dust Filter and a Filament Runout sensor to the direct drive mod. I installed a BLTouch, using the Z Limit Switch as a filament runout sensor. I noticed that the tip of the limit switch had to accept filament in both directions. If a...

This direct drive mount is a remix of the TEVO Tornado Bondtech BMG direct drive mount (remix), found at https://www.thingiverse.com/thing:3995514, courtesy of QCPassed. It fits the Ender-3 and will also fit the TEVO Tornado as well as the CR-10(S)...

Got this direct drive for an ender 3 from a friend and thought I would try to use it on my Megazero 2.0 So if you get your hands on this setup then this maybe for you I also have Ender 3 V2 which is already heavily modified so I does not need this......

This is a remix of Bart-tech3D's simple conversion to a direct drive extruder on Ender 3. ... The original can be found here: https://www.thingiverse.com/thing:3965738 this is designed for a stepper motor and a dual filament feeder that can be...

I got this cheap direct drive plate for my Ender 3 since I cba importing the printermods plate which is actually a little taller than what the original part was made for. This increases the height of it by 2mm to compensate for it. NOTE: I also...

I designed a simple Direct Drive mount specifically for X-Axis linear rails on the Ender 3. The existing direct drive mount needed to be replaced after I added an x-axis linear rail, so I created this new one. M3 threaded inserts were used for the...

I use Creality's direct drive setup for my Ender 3 Pro, with a swapped out hotend with an all metal Swiss Micro one. However when my plastic extruder arm broke at the filament wheel... I decided to upgrade the extruder to a metal one from Creality.

I have an Ender-3 V2 with a BIQU H2 direct-drive extruder. And I like mounting the spool holder on my printers, but this doesn't work super well with direct-drive extruders. So, I wanted to install a reverse Bowden setup to put the filament...

I also made the rim taller so there's even less of a chance of the spool falling from the mount.For the “clip” part and print instructions visit the original design:...

These parts are designed to be used with Benawhite's Ender 3 Direct Drive Adapter (https://www.thingiverse.com/thing:3386628). They replace the "stepper_spacer.stl" file, offering a spacer that provides support for the stepper motor and a filament...

These parts are designed to be used with Benawhite's Ender 3 Direct Drive Adapter (https://www.thingiverse.com/thing:3386628). It replaces the "stepper_spacer.stl" file with a spacer that also provides a support shelf for the stepper motor, as well...

Printable ender3 direct drive upgrade compatible with Orbiter V2.0 Extruder.

The other mod that may be of consequence is that I am using the Hero Me Gen3 by MediaMan and the subsequent remix of the main duct itself (due to the Direct Drive kit changes) by TeachingTech who also reviewed the direct drive kit on his Youtube...

I made this for the stepper motor on the official Creality direct drive upgrade kit for my Ender 3 Max. I realized it fit perfectly on the QR code as well but had to remove the right side of it for the X axis switch. Included is the versions with...

In my opinion it is the BEST direct drive mount for the Ender 3. You lose NO Z height, and you can easily see the extruder while you thread filament in. I have been using it for many months very happily! This remix only includes the DUEL GEAR...

convert your Ender to direvt drive with only one simple print and minimalistic modification to your existing setup 

I initially wanted to make a slight modification to the SpeedDrive v1 - Ender 3 direct drive mount by sashalex007.\r\n\r\nThe goal was to make it lighter and get back the full length of the X axis, as the original design limits it...

*******Updated Jan 11 2020 with link counts and spool holder\r\n******updated jan 15 2020 with correct drive mount link \r\n\r\nI'm Not the Designer, I Just Converted My Printers!\r\n\r\nNone of these designs are mine nor have they been altered or...

I designed this very basic part as I wanted to mount the Ditan Dual Extruder as a Direct Drive on my Ender 3. I had been using the Ditan for a while as a Bowden Setup and was very impressed with its design and performance, but wanted to reduce the...

A simple remix of kyoday design, in order to fit it in my direct drive Ender3. ...Also increased the thickness of it.

Remastered for managing the cable assemblies heading to the hotend and extruder during a direct drive upgrade. ... Upgraded with a bigger loop design.

Simple remix of my  sturdy direct drive adapter, which itself is a remix of Ben White's direct drive extruder.Adapted for use with the cheap dual gear extruder which can be bought for around 10 - 14$ on aliexpress and similar sites

A direct drive mount for an Ender 3 with a BL-Touch, a E3D v6 hotend, a BMG extruder and a pancake motor inspired by "The Tank" hotend with better cooling and filament path. Print instructionsThis is inspired by "The Tank" mount (but not a remix)...

This mount allows you to attach a dual gear extruder on the bracket included in the Creality direct drive upgrade kit.I printed mine in PLA and it seems to work fine so far.

For dual-drive - bmg clon (thickness - aprox 34 mm). https://www.aliexpress.com/item/33009489647.html?spm=a2g0s.9042311.0.0.27424c4dkIjaqh Print instructionsCategory: 3D Printer Extruders Summary For dual-drive - bmg clon (thickness - aprox 34 mm)....

A direct drive mount for most creality printers to allow mounting Dragonfly BMS, Dragon or Mosquito hotends with either Sherpa mini, Orbiter 1.5 or Orbiter 2.0 extruders.It also integrates a 5015 blower fan part cooling duct.Assembly requires the use...

I converted my enter 3 to direct drive but didn't have room to mount the spool above the printer. This meant the filament came in at a sharp angle and the spool would start rocking as the head pulled the filament back and forth.  This uses 6mm...

I converted my enter 3 to direct drive but didn't have room to mount the spool above the printer. This meant the filament came in at a sharp angle and the spool would start rocking as the head pulled the filament back and forth. This uses 6mm airsoft...