direct drive ender 3 3d models

Direct Drive Ender 3 with Bondtech gear extruder. With thanks to Vas Parshin for the Bondtech extruder design.The positioning of the extruder steppenmotor is turned 90º. ...This way the motor is better supported than with the motor facing to the...

Printed with support only on lips for Direct Drive module and under Base 0.2 Modified this thing : https://www.thingiverse.com/thing:3589452 to make it work on here

My personally ender 3 profile with direct drive and dual gear

Directly head to the Ender 3 Pro using manual drive. Use adhesive to secure the stripe holder, X-axis limiter and cable holder in place. ... Reaching a satisfactory retraction setting of 0.5 millimeters per second has been achieved at a speed of 50...

This model allows to switch to direct drive (useful to stabilize the weight and for flexible filaments), no parts to buy except 2 screws to replace in longer for the cooler IMPORTANT POINT = no loss of dimension on the tray with this support This...

Direct drive upgrade for the Ender 3 using stock, hotend, shroud, and extruder. Designed to work with "Quick tool change for Creality CR-10 / Ender series by ProperPrinting". ...v3 is the one that is the closest to being complete, it is usable but the...

Voilci un kit de pièces à imprimer pour transformer son ender3 en direct drive.

Too many times I have found myself having to dismantle my hot end assembly in order to remove the direct drive mount just to take care of a clogged nozzle or an extruder gear issue. But not any more! I present to you, Thingiverse community, a...

...I strongly advise against printing this version for a standard Ender 3. For stock models, please refer to Thingiverse: 3562807. Important note: If you're planning to print with high-temperature materials like PLA, don't use the original PLA shroud.

You will need the following parts 1 threaded 6mm of ish 150mm 2 M6 Nuts / Lock nuts 2 608zz bearings Super glue 4 T-nuts M4 4 M4 screws with alen head Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2...

Hi there - i was looking for a robust and good spool holder to mount on top of my Ender 3 v2 I recommend my filament guide here https://www.thingiverse.com/thing:4712122 to fit in front of the spool holder. There was some but was really not...

Hi there - i was looking for a robust and good spool holder to mount on top of my Ender 3 v2 I recommend my filament guide here https://www.thingiverse.com/thing:4712122 to fit in front of the spool holder. There was some but was really not...

Direct drive pour Ender 3 en deux parties. il faudra de la colle forte pour maintenir les deux partie ensemble, et des insert laiton pour le montage! prevoyez quand meme un cable pour le moteur de 50 Cm de plus! ...;)

I edited this for better angle for hotend mount and to be able to mount it on https://www.thingiverse.com/thing:4173248 this fan duct

Model contains 2 adapters plates, 25mm works with bmg dual drive extruders and 10mm works with original extrusion system.

Another Ender 3 direct drive filament support.

BLtouch mount for Ender 3 Pro Microswiss Direct Drive kit, offsets the BLT 60 degrees, enabling you to take the standard Ender shroud off without removing BLT.

This manual applies specifically to using direct drives on an Ender 3 to prevent the filament from popping off the spool's edge.

I created this bracket so my cables for my ender 3 pro direct drive 3D printer stay in the best position. With this bracket the cables will never interfere with your print. When you go to direct drive you need to extend your drive’s wire. Have...

This is a remix from "https://www.thingiverse.com/thing:3437455/remixes" modified to fit with this Direct Drive mount "https://www.thingiverse.com/thing:3373107" I've been using this Direct Drive mount for years on all of my Ender 3, it fits like a...

This is a remix from "https://www.thingiverse.com/thing:3437455/remixes" modified to fit with this Direct Drive mount "https://www.thingiverse.com/thing:3373107" I've been using this Direct Drive mount for years on all of my Ender 3, it fits like a...

I was using https://www.thingiverse.com/thing:4742800 with stock ender 3 v2 but upgraded to Micro Swiss NG direct-drive and hot-end. I wanted to reuse the endoscope holder I had already and just mount it to this fan shroud. ... This endoscope is...

I created this bracket so my cables for my ender 3 pro direct drive 3D printer stay in the best position. With this bracket the cables will never interfere with your print. Have fun printing it and leave comment! ... You can see for other design on my...

Update December 3, 2020 I remixed fan duct and made my own direct drive bracket. https://www.thingiverse.com/thing:4674061 Update: November 25, 2020 I uploaded a couple of photos and another cable cap that covers the entire cut out. One photo...

Snap-on cable chain for Ender 3 pro converted to direct drive using Madau's excellent direct drivinator https://www.thingiverse.com/thing:3589452 This is a remix from https://www.thingiverse.com/thing:4309158 and the upgraded cable chain from...

I converted my Ender 3 v2 to direct drive, so i wanted to mount my filament spool like on Prusa's, but didn't want some chunky and time consuming print. So here it is EnderSpoolHolder Prusinator. It is made for M4 screw, also aded the screw...

needed a mount to fit the ender 3 pro

remixed to be compatible with bmg and hero me gen 5 ender 3 V2

Modification of "remix" for ABL + V6 + BMG, to fit Ender 3 Pro with NF-Crazy (mosquito) and BMG.

My vision of hanging direct drive with BMG and E3Dv V6 with short bowden Everything fits in the frame. Changes in marlin are PID, #define NOZZLE_TO_PROBE_OFFSET {-10, 8, 0}, // @section homing // The center of the bed is at (X = 0, Y = 0)   // #...