dime model

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

Please review the filenames, model file comments, and pictures before starting.Non-printable parts and necessary tools:The clock movement and clock second...

IF YOU ARE HAPPY WITH THAT, A LITTLE DONATION WILL BE VERY NICE <3https://www.paypal.com/donate/?hosted_button_id=5F525DYM8GXK4 If you want to do a remix or changes to the design, you can get the Fusion 360 and STEP file here:...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

35mm diameter)Electric cablesElectric soldering iron and solderAn M4 screw with its corresponding nut (approximately 15mm in length)Two appropriate screws for fixing the DC motor to its support (depends on the type chosen)Instant glueStep 1: Print...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

 A side note - you also probably should be using my rear PC4m10 jack for your MMU3 https://www.printables.com/model/542409-mmu3-pc4m10-rear-connector The perfect length is one make an even curve downward and the up into the back of the MMU that is...

-This current model is built under the assumption that most people will be using this with old tablets (or phones) that they would have thrown away otherwise, so taking a tablet (or phone) off of the top slider isn’t a smooth and seamless experience...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

Learn everything about the V-Core 3 on the dedicated project page: v-core.ratrig.com. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware)...

# Reddit Post For anyone who want to try this themselves, I created my own "Cloud Streaming Console" by taking a few components I had, modded the plastic on a Gamesir X2 Pro controller, modeled and 3D printed a basic "shell" with some handles and...

○ 3 options available § EyeCuSmile_Ribs_V2_RoundedNose.stl - best visibility § EyeCuSmile_Ribs_V2_TriangleNose.stl § Or various developmental ribs models used in the flat pack face covering kit and Version 1 listing of this design. - COMMON...

The 3D printing process sometimes leaves whiskers or small blobs of plastic which might jam the fully assembled power train unless each stage is run-in until all parts are worn smooth when the whole will operate as designed.&nbsp; &nbsp;Assembly:1)...

From there I just drew out the parts and extrudede them in the modeling tools, then exported them to STL files and printed them out. Project: Laserscythe - Another Open Source laser engraver using recycled doohickeys Project Name: Project:...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

If you're using the motor in the BOM or Qidi stock motors use this: xmax-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xmax-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print like you would...

The ability to visualize 3D models in real-time enables users to make informed decisions about color palettes, proportions, and overall aesthetic. This level of precision is unmatched by traditional design methods, making Shining 3D Fashion a...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

In the end I think the best way is to simply open up the 3D-model of the whole maze and just put obstacles together one by one. Therefore I Added a few different files (STEP, STL, 3D-PDF (<a...

If you're using the motor in the BOM or Qidi stock motors use this: xplus-imate-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xplus-imate-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print...

rice or sand.Glue if the press fits are not tight enough&nbsp;Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Real quick: Check out my other S22 designs like my LED handle/boomerangs, help me spread my design by hitting the like button, post a photo as a make once you've printed things out!! There's an active community on this, come:</p><ul><li>join the <a...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

Have a close look at the photos and assembled model (wall_clock_07.stl).PlatesThe bearings are hard to push into place, this is where the bench clamp comes in useful to push them flush into the plates.The front plate needs a 30mm M3 screw to hold the...