diatone roma l5 3d models

I'm Not Afraid of You, I'll Fight Back

Patient with L4-L5-S1 spondylodiscitis, initially required urgent decompressive laminectomy due to compression of the spinal canal, followed by a course of antibiotics.

Long extension antenna for new Vista

Remixed from the linked design and https://www.thingiverse.com/thing:5425766 I merged both designs to have a triple mount for a crossfire antenna, a dji vista / o3 and a GPS BN-220 while simplyfing the design to eliminate xmplus antenna holders...

Very easy to print with PLA hard plastic, works verygood for long range, I Tested it middle range about 1km

Sized specifically for the Matek M8Q GPS but should work on similarly sized units.

Printed from TPU with 100% infill. Holds the antenna pretty well. ...I'm using the u.fl version of them so the cables are pretty long (that's why the sleeves are so high up)

As in the title. ...Other tilt angles on request.

This is my usefull cage to fix any stuff (receiver, beeper, etc) simply a the back of this quadcopter. ... Once it is printed you can cut it where ever you want to simplify the mount

Perfectly fitting Antennamount for the Walksnail V2 VTX.

I use M2.5 8mm bolts. And, 2.5mm washer. ... infill : 20% TPU

A partial covering mount to save a little weight. ... Compatible with TBS ND filter.

A vertical mount that interfaces with the hole in the top plate. ...Print in TPU for best results.

Wrapped the wires and the GPS BN-220 itself into copper tape, connected GND and moved the GPS "above" the DJI VISTA unit. ... Fixes the "GPS fix issue" for me -> got 9 satellites in 2.5 - 3 minutes (cold start) Update 02/2021: 17 satellites in...

all in one rear mount for hglrc m80 gps + tbs immortal or elrs RX atenna + small buzzer.

A partial covering mount to save a little weight. Compatible with TBS ND filter (you can just about see one attached in the rear photo) - I am not sure who originally designed this so won't include this in the files or link to it but easy enough...

Mounted with two M3x9 screws in the front. Vibration reduction structure with three damper legs for clean gyro data. Perfect for GoPro Hero 7 with RSGo. ...20 degrees tilt.

<iframe width="560" height="315" src="https://www.youtube.com/embed/2kZIEd7LzRc" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> Enjoy

I suggest for an easy install of sma port to make a cut from the front into the hole. Then you can easily slide the sma connector into the hole. ... GPS used : Beitian BD-280ZR 28 x 28 x 8,4 mm

Хвост для популярного дрона, включает установку штатного разъема SMA, GPS типа Beitian BN-180 или штатный, и корпусного разъема XT60E-M (нужно подрезать выступающие уши). С моих хвостом решается проблема плохого приема спутников, так как GPS больше...

i added full dji anteena moutns to this exsisnig design im amatur i made it in tinker cad

Specifically designed for the Matek M8Q GPS with sufficient distance from the frame for quick sat lock.

Хвост для популярного дрона, включает установку штатного разъема SMA, GPS типа Beitian BN-180 или штатный, и корпусного разъема XT60E-M (нужно подрезать выступающие уши). С моих хвостом решается проблема плохого приема спутников, так как GPS больше...

Roma keychainVisit our collection for other soccer team keychains!https://www.printables.com/it/@3dingo_1853196/collections/1289392 ____________________________________Portachiavi RomaVisita la nostra collezione per altri portachiavi delle squadre di...

Spacer Bolts M3 L5

Spacer Bolts M3 L5

Ferrari Roma

I just acquired a generator equipped with an L5-30R outlet and two standard 20-amp plugs. ...Whenever the L5-30R is idle, I opt to protect it by covering it up, which inspired me to create this gadget.

Customized version of https://www.thingiverse.com/thing:739573Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573