diatone gt r349 3d models

Diatone's compact powerhouse, the GT R349, is a remarkable build that has consistently delivered impressive results. It achieves breathtaking speeds and performs acrobatic stunts with ease, rivaling those of its larger 5-inch counterparts. Available...

My receiver was a bit loose, so I needed something to keep it stable and secure within its diatonic range of R349. ...That's why I opted for a simple solution - just take off the canopy and insert the unit into the stand-offs, and that's all set!

... small yet effective to get the job done. Link to the VTX Antenna Mount I also made for the R349: https://www.thingiverse.com/thing:3317546 Link to the TBS Crossfire Antenna Mount I also made for the R349: https://www.thingiverse.com/thing:3317512

Since it has zip ties and now a Crossfire antenna holders it hard to level this thing so i just made something small and simple to do the job. Link to the VTX Antenna Mount that I also made for the R349: https://www.thingiverse.com/thing:3317546 Link...

This is a dji digital fpv conversion kit for the diatone r349; you'll need to: 1) Replace the default stack with the GEPRC toothpick 20A aio board (https://geprc.com/product/gep-20a-f4-aio/). Note that this board will be elevated so the motor leads...

A super simple way to mount a caddx vista & DJI camera to the diatone rabbit R349; note that the original stack has been replaced with a geprc 20A aio flight controller. This 3d-printed components of this project consist of three-parts: 1) A...

Diatones canopy is slightly too small to accommodate the DJI Caddx VTX so this was designed to hold the new antenna and arch over the VTX. Large cutouts around the camera were necessary for prop clearance and yes it does kinda leave your expensive...

Diatone GT M3 Spare Upperarm Assembly

... for the arm ends, which can also be mounted under the motors for added "soft mounting" support. In addition to these parts, I'm using the Diatone GT-R90 Receiver Shelf, available on Thingiverse as this project. ... Thanks for taking a look!

I've created two sides and one top plate for the Diatone GT M515 to safeguard its electronic components. The top plate is specifically designed to accommodate a Foxeer Lolipop. These parts were engineered with an ultra-light design, ensuring that...

So I was out flying with my GT-R90 drone from Diatone when suddenly I experienced an extremely severe crash that ended in a catastrophic failure of the frame. I just couldn't wait to get a replacement frame sent, so I decided to design one myself...

This is a Remix of the 3D printable Arm for the Diatone GTM3 (2018) Model. ...I made it a little bit thicker as the OV.

Diatone's little 3 inch monster the GT R349 is an amazing craft and has a proven track record. It achieves astonishing speeds and all the acrobatics of a 5 inch. With the Caddx Nebula v2 coming out, it was time to convert my favorite 3 inch to the...

Mounts for the bn180 GPS module are designed specifically for the diatone r349 rabbit 3" quadcopter. I've only tested the vertical mount, as it keeps the GPS closer to the frame and provides better protection. ...A horizontal mount was created in case...

I'm using a mount specifically designed for the BN180 GPS and Foxeer Lollipop antenna on my Diatone Rabbit r349 drone. The BN180 is positioned horizontally, which isn't perfect but appears to function well enough for me. ...Make sure you point the BN180...

Rapid Mount Solution for Diatone R349 and Realacc UXII Stubby VTX Antenna. Intended to Attach Over Top of Quad's Canopy Mount, Not Directly to Stand-Offs. Snug Fit Ensures Minimal Exposed Antenna, Which May Impact Signal Strength. ...Need Further...

This is a BN-180 GPS Sensor mount that fits my Diatone R349 HD MK2. It holds the GPS very securely. I was able to zip tie my receiver (R9 MM) to the bottom of it, as well. Which is really nice to free up some space. I have not checked to see if...

This is a BN-180 GPS Sensor mount that fits my Diatone R349 HD MK2. It holds the GPS very securely. I was able to zip tie my receiver (R9 MM) to the bottom of it, as well. Which is really nice to free up some space. I have not checked to see if that...

fits diatone gt-m series

I needed to attach my TBS Crossfire Antenna to my new Diatone 2019 R349, so I came up with this design. It should work on the R249 and probably the R239 as well. Everything was printed in TPU, and I used the default FLEX setting on my Prusa MK3, but...

Needed to mount my TBS Crossfire Antenna to my new Diatone 2019 R349, so I came up with this design. It should work on the R249 and possibly the R239. I printed everything in TPU. I also used the default FLEX setting on my Prusa MK3, but i turned on...

Diatone GT-M3 RX holder stands upright proudly

This human being appears to be associated with the Diatone GT-M series of products.

Propeller guard designed specifically for the Diatone GT-R90 drone, engineered to provide optimal protection and stability during flight operations.

I'm working on designing a simple wall hook to securely hold my trusty Diatone GT-R90 drone.

Here is my revised version of the text: High-performance arm fairings designed specifically for the Diatone GT-M5 and GT-M200 models are being developed to significantly reduce drag and turbulence on arms, ultimately enhancing corner handling during...

A replacement rollcage for the Diatone GT-M3 fpv drone. I've since switched to the HGLRC Arrow 3, hoping someone else gets use out of it. If you don't want the built-in standoffs on the left side, simply mirror and print the right side instead. The...

It's specifically designed for use with the Diatone GT-M3. The propnut wrench is versatile and can handle both M5 hex screws and any situation where an 8mm wrench is needed. ...We've also included a redesigned engine wrench that allows for easier...

The Diatone GT-M5 Fairing V2 is engineered to minimize drag and turbulence around the arms, thereby enhancing flight performance during high-speed sharp turns. Although I didn't notice a significant difference with the V1 version when the camera...

This upgrade has proven to be perfect on my Diatone GT R90 drone when printing in Prusa Flex (semi-hard flex material), allowing me to crash into gates without any issues. ...In contrast, ABS and PLA materials are too brittle for my hard-crashing style,...