df64 mods 3d models

Here are a few mods for the BNB SX extruder. 1) Revised lower clamp with cable support - This is designed to prevent binding when the extruder is on the right-hand side. The normal Bear/BNBSX extruder has its cable support connected beneath the...

I also redesigned the back plate to allow attaching wrist rests and have included the current ones I'm using.  In the pictures you can see the fully modded Sofle, I cut the new backplate out of  frosted 5mm acrylic as I think it looks nicer then the...

All of my mods for my mpcnc primo F-25mm. STLs are oriented for printing. Everything prints without supports, except a few parts. Please refer to the description below and/or the included gcode. XY EndstopsHardware needed:2x M3x5x6 heatset insert, or...

Hi guys, These are some bits and pieces to mod the Injora Buggy Bouncer. Overview of 3D parts here: https://youtu.be/MvJFd2ElRg0 Bouncer Build Guide here: https://www.youtube.com/watch?v=KtU9XnC91Hw XR247 Axles Guide here: ...

Hi guys, These are some bits and pieces to mod the Injora Buggy Bouncer. Overview of 3D parts here: https://youtu.be/MvJFd2ElRg0 Bouncer Build Guide here: https://www.youtube.com/watch?v=KtU9XnC91Hw XR247 Axles Guide here: ...

You will need to re-tune your extrusion steps after this mod. Print instructionsCategory: 3D Printer Parts Print Settings Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 50% Notes: All parts should print without support in the...

Mods for an Ashford table loom The sectional beam dividers allow loading a warp with sectional tools like AVL's warping wheel or a spool rack. In addition to the dividers, you will need 4 dowels that fit the holes. I drilled mine for 5/16" dowels. I...

... the top of the funnel wider so it fits into the bellow very snug and tight. I was inspired by CY’s mod that can be found here: https://www.thingiverse.com/thing:4899743. ... My version has a clean ramp without lines and a bigger opening (22 mm).

This remix split the part right in the middle, with 2mm holes to align with a bit of filament while gluing both parts together. ...With a bit of sanding and spray paint it, you can hardly see where the seams are.

UPDATED VERSION: https://www.thingiverse.com/thing:4901872 - popcorning is further reduced an bean flow into the grinder is improved Infill 20 % no supports Intended to reduce popcorning and improve the process of bean feeding into the burrs.

I only added the ability to tighten this at desired height, there is a similar thing by [greggers](https://www.thingiverse.com/thing:4866360) But i like this indicator design as it's a bit minimal (only 3mm height) and clear view on numbers. ... ...

Provides protection against popcorning and, by extending the funnel, allows for all the beans to sit inside the funnel. With shorter anti-popcorn funnels, some beans sit on the bellows and have to be manually pushed down. If you are also using the...

This remix split the part right in the middle, with 2mm holes to align with a bit of filament while gluing both parts together. With a bit of sanding and spray paint it, you can hardly see where the seams are. ... Category: Kitchen & Dining

These mods are for LRP Rc cars.

Upgrade mods PLA+ all infill 30%

1) A rotor mod with tighter tolerances on the faces of the rotor for better air sealing (less bleed-by during start-up & low speed) 2) A case mod with rounded inlet/outlet holes for improved airflow transition (high volume/high speed operation). ?)...

Made some new mounts for the Printer mods direct drive kit for the Ender 3. The original mounts would kink the extruder cables, you might need an other 3mm x 50mm shcs bolt for the extruder mount, I only put one in because the bracket was tight and...

This is a match saver for the Monkee Mods Colonel Wasp Firelfy blaster. Use some glue to secure it to the blaster. ...

Eureka Mignon Single Dosing Mods Include/s: Tilt Stand (PLA) Single Dose Square Hopper (PLA) Square Blow Out Bellows (TPU 45A)

Example mods for My hair claw, just to give you an idea. ... Demo: https://www.youtube.com/watch?v=bwwVEAOaNjE Hair Claw demo: https://www.youtube.com/watch?v=J0_RxDkBPk4 Make your own mod, there is a file for the right size of insert. ...

Mods i've created for the spirit halloween proton pack. ...Not gonna lie, these mods require you to cut the hell out of the pack, but what you end up with is a much more authentic looking proton pack. ... Good Luck -AV

This is my set of modded parts to make it compatible with Prusa MK3(s) extruders or the many community modded extruders. Print instructionsFor more details about this build and mods please read my build thread in the V1 forums. Currently only the Y...

Hair Claw demo:Make your own mod, there is a file for the right size of insert.

Mods for planner fx 707s from banggood. Motor mount - Hole for motor 2 mm without 12 mm. I use motor Dys 1806 2300 kv. ...Base for matek f411 WSE.

A couple mods I use for the Flite Test F-18. ...A center rail grip for help with hand launching and some tail fin stabilizer brackets which also have tube if you do the push rod modification.

For this mod you need to use the Bumper mount remix -Wheel Shafts M4 Remix Use this mod to convert the front and rear axles to M4 studs instead of M3 screws. ...You'll need M4 threaded Rods cut to length for the rear and 2x 25mm screws for the front ...

Joystick Mods for your PowerA switch controller. Leftstick: Larger thumb area Rightstick: increased height for finer movements Both are designed specifically for the PowerA Switch controller (enhanced version in photo) and are friction fit. ... Photo...

http://www.thingiverse.com/apps/customizer/run?thing_id=341856 Instructions Using the following settings: Label Text: DBS MODs Include Stakes: Yes Font: Write/Orbitron.dxf Font Thickness: 4 Build Plate Selector: 0 Manual Build Plate Y Position: 100...

For this mod you need to use the Bumper mount remix-Wheel Shafts M4 RemixUse this mod to convert the front and rear axles to M4 studs instead of M3 screws. ...You'll need M4 threaded Rods cut to length for the rear and 2x 25mm screws for the...

Mods should use Turnigy or Bluebird 210dmh servos on the V-Tail of the Believer FPV aircraft. The four parts include: 1. A servo mounting insert that adapts to the size of the 210DMH and adds proper spacing. 2. Custom-made servo horns designed to...