dewalt dwe7485 table saw dust collection adapter by 3d models

Adapter for my Bosch GTS 10 XC Table Saw Dust Port to 100mm Chip Extractor Hose. The outer section of the large side measures 100mm in diameter, featuring a small lip designed to prevent the hose from slipping out. The smaller side tapers gradually...

Designed a dust collector/extractor assembly for the DeWalt DW6184 fixed router base commonly used with the DW618 router. Uses (2) 1/4-20 x 4" screws and wing nuts to attach the two halves. ...This design does reduce the maximum extended height of...

Designed a dust collector/extractor assembly for the DeWalt DW6184 fixed router base commonly used with the DW618 router. Uses (2) 1/4-20 x 4" screws and wing nuts to attach the two halves. ...This design does reduce the maximum extended height of the...

... using Tinkercad. ... I created two versions: one with the dust port in the middle and one offset. I prefer the offset version because it provides more clearance. This setup enables me to use a regular flexible hose that attaches directly to the saw.

Dewalt Table Saw Miter Gauge Holder This is a bracket to hold the miter gauge on the saw frame when not used. Currently dewalt has no where to hold it, that I can see. The protractor/angle gets set at 10 degrees, and then that guide will sit flush...

I bought a Dewalt 7491 Table Saw last week and I'm absolutely loving every minute of working with it. This is a dado throat plate needed to install or use a dado blade. The dimensions were based loosely on the standard Dewalt throat plate, minus the...

Full credits to: https://www.thingiverse.com/thing:2893293 The t-nut/t-track wasnt the right fit for a Dewalt saw (specifically Dewalt DWE7491-XE) So I made my own to fit. This may well work on other saws which have the follow dimensions for the...

I made it for my Ryoby table saw for adapt my vaccum Karcher WD5 on it. Easy to us and work perfectly. ... Print it without support.

Enter our hero - an adapter that mounts to the hose using the posts on the dust port to keep everything securely attached. It's simplicity itself! This little number is a 3-part print job, with two halves clamping around the hose end and the third...

Printed both of these with Priline TPU to use as a vacuum adapter for a Shopvac: 1.) "VacAttach_Hitachi to ShopVac v3.stl" for a Hitachi 12 inch chop saw 2.) "VacAttach_Delta 10 inch Chop Saw to ShopVac v5.stl" for a Delta 10 inch chop saw Uploaded...

Adapter clamps to the dust collector splitter thing using a hose clamp, then hose slides on the narrow end of the adapter. Print with the narrowest opening face down on the plate with a brim enabled. ... Here is what I used as far as print...

I designed a system to capture sawdust from my Ryobi Table Saw by placing a board beneath it and cutting a hole in its center. Next, I 3D printed a funnel-shaped attachment for my shopvac, which I purchased at Harbor Freight. The design includes a...

I bought a cheap 1/4 sheet pad sander off amazon to make sanding some drywall easier, but it had an odd dust collector output nozzle. The small end fits inside the sander's output nozzle - i added one wrap of masking tape for a bit of 'stiction' The...

Adapter to go from a 2.5" flexible PVC dust hose to the 1" dust port on my Dewalt orbital sander. ... Printed in TPU, makes for easy install and a solid fit.

Being unsure about utilizing the dust hose adapter located at the rear of my Harbor Freight 10-foot 13-amp table saw, I came up with a custom-designed connector that accommodates not one but two distinct sizes of tubing.

If you already have an indicator and you want use the jig as is, it is important that the mounting diameter of the indicator is 8 mm and the distance from the center of the spindle to the back is also 8 mm.You need:all printed parts (4 nuts, 1 base,...

Vertical adapter fits 1.5" vac hose, Lateral adapter fits standard rigid 1.75" Attached sldprt file if you want to customize for your dust collection setup. OnShape search dw616 dust shoe and copy / modify. .8 nozzle, .32 resolution - 2mm wide...

I needed a way to catch all the sawdust flying out of my Ryobi Table Saw, so I placed a board right underneath it and cut a hole dead center. Then, I 3D printed a funnel vacuum attachment that snaps perfectly onto my shopvac from Harbor Freight. The...

I required a method to gather the sawdust spewing out of my Ryobi Table Saw, so I positioned a board beneath it and carved a hole in its center. I 3D printed a funnel vacuum attachment to link my shopvac that I purchased at Harbor Freight. The...

I just added the Dewalt DWE6423 Sander to my collection and I'm having trouble with the small dust collector. I already ordered a 32mm hose (https://amzn.to/3c3aisv) on Amazon for other purposes, so I can connect various devices to my shop vacuum.

I adapted this design from Elproducts, modifying the hose size to accommodate a 2.25 hose and adjusting the dimensions from 120x120 to 140x140. ...I created this model using Tinkercad and you can edit it online at...

Dust Hood Adapter for Dewalt DW50 type Planer. The Adapter can be used for jointing and planing like the original 2x15mm magnets with 4mm hole can be added to fix the adapter to the chip deflector, or alternatively by sticking two carriage bolts in...

This is an adapter for connecting a vacuum with a 1 7/8" hose to the Dewalt DWV9000 Universal Connector (which then connects to the compatible tool of your choice). I have a shop vacuum with a 1 7/8" hose and was trying to figure out how to interface...

This sleek Dust Collection Hood encases the saw blade, meticulously collecting every scrap of sawdust. With a compact printer at my disposal, I broke down the design into manageable pieces and expertly dovetailed them together, eliminating the need...

In rearranging my workshop I wanted to put the mitre saw as close to the wall as possible by adding a 90-degree elbow to the dust port for connecting a vacuum hose. I designed this in OpenSCAD and have a great fit with a tapered end that goes into...

This allows you to connect the dust port from a Dewalt cordless random orbital sander (DCW210) to a Ridgid wet dry vacuum (specifically the WD4070). It came off the printer a little rough but fully functional. The design has been adjusted so it...

... of tools. ...but I believe shop vac hoses are pretty standard at 1.75". The dustport on the table saw is a little strange at 2.55" I printed it with solid infill but I'm sure it'd be fine otherwise. ...It's a bit thicker than most adapters at .095"

For dewalt tracksaw DCS520b Converts to 2.5" flexible hose for woodworking tapered fit on both ends for snug fit.