dewalt 18v to 12v adapter 3d models

Adapter allowing Dewalt's DCW210B sander (or any other tool compatible with the DWV9000 adapter) to a Festool 27mm dust extractor hose, with or without the twist-lock mechanisms each connector allows.This includes four versions, one for each...

A connector specifically designed to link a DeWalt table saw's vacuum port directly to a standard five-gallon Shop-Vac hose is available on the market.

Adapter for a Dewalt DWE6423K (and probably others). Printed in PLA, but the tabs are brittle. ...The filament I used was old, but it still may be better in PETG or ABS.</p>

&nbsp;I recommend setting PrusaSlicer to put the seams in random location on the ring (bulges from "aligned" or “nearest” seams will likely create welds between the separate parts), and definitely consider taking advantage of the new fuzzy skin...

This is an adapter sleeve that will fit over the 63 mm (OD) DeWalt DW735 benchtop planer and accept a 57 mm vacuum hose collar (like the end of a Shop Vac hose). It was designed using FreeCAD v0.18 with the Loft and Thickness tools, with a wall...

Dewalt DCW210 Cordless Sander to Festool Cleantec Adapter This adapter allows a Festool Cleantec dust extractor to be used with the Dewalt Cordless sander (O-Ring also required). This sander is generally a good design with the exception of the...

This is a compact battery adapter for Craftsman 20V tools to use DeWalt 20V MAX batteries. The battery lock does align with the tool but the height difference makes it a very light lock, doesn't really go "click". I saw other commercial adapters that...

When I purchased my Dewalt 12VDC MAX Electric Screw Driver, it had no ability to hold extra bits, so I decided to design one. ...It holds 2 narrow shaft bits and attaches to the Dewalt with a M3-12 screw.

Chamfers have been added to the vac locking mechanism and from the larger cylinder to the smaller cylinder to add strength.  According to Amazon: https://www.amazon.com/DeWalt-DWS780-Replacement-Assembly-N041726/dp/B009L32D7U“Compatible with DeWalt...

A seamless shift from the Dewalt DW735 dust collection port at 90 degrees to 4 inches, where a Rockler quick connect takes center stage, also compatible with a 4-inch flex hose and potentially other fittings, although further verification is...

... redo of a vacuum hose attachment by Thingiverse's https://www.thingiverse.com/thing:2659170. ...This revised version lets you link your DeWalt DW735 planer directly to a Dust Right quick-change dust collection handle, ditching the shop vac altogether.

I wanted to plug my Bosch dust extractor to my Dewalt DWS774 miter saw so I designed this.On the first version the hole for the vacuum lock was a bit wide so I reduced it on the second version. I also reduced the nuts' ears and added footprints for...

Another crucial addition to any comprehensive cleaning kit is a versatile vacuum hose port adapter.

Use this design to step down the lower 2.5-inch vacuum port on a DeWalt table saw to the 1.75-inch vacuum hose of a DeWalt shop vac.

Adaptator battery hitachi 18v to parkside 18v Adaptateur de batterie parkside vers hitachi x18

A 90° degree transition from the Dewalt DW735 dust collection port to 4". Here I'm using a Rockler quick connect but it'll also work fine with a 4" flex hose and it may work with various other fittings but I haven't verified this. The Fusion file is...

This is a Bosch 12V (10.8V) Battery Adapter for Black & Decker Tools 12V. Important Note: Bosch batteries do not come equipped with Over-Discharge Protection. ...Exercise Caution and Consider Installing an Li-Ion Over-Discharge Protection Board to...

https://www.thingiverse.com/thing:3877970 was designed for different blade size than the ones used by my planer. ...To better fit 260x21x3mm blades I've designed this adapter

Yet another vacuum hose port adapter. ... Category: Tools

Made this little adapter so I could install a standard 12v relay into my Infiniti fuse box, hope this helps someone else in the same situation.This should fit most Bosch 12v relay sockets and the locking tab should fit any Nissan/Infiniti and most...

Made this little adapter so I could install a standard 12v relay into my Infiniti fuse box, hope this helps someone else in the same situation. This should fit most Bosch 12v relay sockets and the locking tab should fit any Nissan/Infiniti and most...

Slightly smaller version for the 12v drill.

A step down and re-direct adapter I made for my Planer to connect to my shopvac. My dust collection set up can't keep up with the ejector fan on the planer, so I have to go direct to my Rigid Shop vac. Even at this point if I shut off the shop vac...

Fits snuggly onto the DeWalt 18V drill tool, but not as good a fit for other DeWalt 18V tools. The two models are the same, except the plus version has an extra 15mm for clearing, if you have a steel holster clip attached to the machine. Designed...

The Bosch Adapter connects Bosch Professional 12V tools to the Bosch 19mm Tube. The tool attachments are too small to fit directly into the tube, so this adapter is necessary. Testing was done with the dust extraction attachment of Bosch Professional...

The base of this is not mine, but i tinkered it to fit the DeWalt 18V Li-Ion batteries as those are the one i have and i liked the design of this

You'll need to convert your standard 1-1/4 inch vacuum hose to accommodate Dyson attachments effectively.

I have a DCW604 router and Makita tracksaw. ...I was going to spend the $50-$60 on etsy to buy an adpater but It defeats the purpose of 3D printing to post a physical item. So I made my own. ...Have included the fusion file to make changes if needed.

... ...(http://www.thingiverse.com/apps/customizer/run?thing_id=97238). To guide the fabrication process, utilize these specifications: insideVacuum = 32, $fn = 45, outsideBandsaw = 58, vacuumLength = 45, bandsawLength = 24, and wallThickness = 4.

The tool to create your own versions. Use http://www.thingiverse.com/apps/customizer/run?thing_id=97238 for customization. Instructions Options are below. ...Here's what you can customize: * vacuumLength = 40 * insideVacuum = 31.5 * outsideBandsaw =...