developing tank minox 3d models

Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. ... Helps to taper film of feed end OTHER SIZES ARE HERE 110/16MM - https://www.thingiverse.com/thing:4831133 17.5MM HIT - https://www.thingiverse.com/thing:4831135

Scaled to fit a Stainless Steel Nikor Developing Tank.Push load type reel.Helps to taper film of feed endOTHER SIZES ARE HERE110/16MM - https://www.thingiverse.com/thing:483113317.5MM HIT - https://www.thingiverse.com/thing:4831135This is a REMIX of...

35mm film developing tank. Should print in ABS or maybe PETG. Print with supports touching bed only. ... STEP file and Fusion file attached as well.

What differentiates it from the earlier design is that it is an upright rotary style tank that uses less than half the chemistry, allowing you to develop 15 meters in just 450ml of liquid, which is roughly the same efficiency of developing the...

This hanger fits into a peg board with 1" spacing. ... It has hooks for the tank, the lid, and the lid cap. Very specific, I know, but hopefully someone else finds this useful.

Tank for developing 120 film.This thing is for those who continue to take photo with film :)

The small JoBo tank is the smallest and least expensive development tank to be used with the 4x5" spindle for cut sheet development and thus often one of the first tools used in your bathroom-darkroom for cut sheet film developing. Unfortunately...

... Also remixed the reel to work properly. If the tank is not fully waterproof, use a gluegun to fill the holes. I recommend to print it in PETG or ABS as those last longer. I will probably make a super16 version if someone's interested. ...

Developing fluids are poured in through the central hole in the tank lid and out through the spout on the side. The tank includes a pouring spout and clamps to hold the lid on. The lid is secured to the tank with sliding tabs, and a vent allows...

Film developing tank, I have designed but yet tested it cuz I don't have access to a printer at the moment. Pieces should screw together, it did not render the screw thread There are 2 versions of the screw cap, one in one piece. ...(dunno how...

This is a fully functional tiny developing tank for developing only a portion (one picture) of an exposed film.

Plastimat developing tank column - 2mm thinner, it would fit 4x5 reel for AP tank into Plastimat tank. Good for stand developing or rolling if you have good seals on your Plastimat tank, as the tend to leak. ... Printed from PMfilaments PETG on Ender...

This is a 4x5 single sheet daylight developing tank requiring 150ml of developer. Simply load the sheet into the dark bag and develop it under natural daylight with ease. ...For fixing and washing, use a small tray, allowing you to observe the process...

This is 4x5 single sheet daylight developing tank. it requires 150ml of developer. You can easily load sheet in the dark bag and develop it at the daylight. For fixing and washing i recommend to use a small tray, its amazing to watch the fixing...

This is designed to motorize agitation on a Paterson film development tank. I based it on my Universal Film Developing Tank. It has teeth to mesh with the teeth on the funnel to mount a 28BYJ48 stepper motor above a 3D printed shaft. The shaft has...

Replacement cap for the plastic lid of a steel developing tank.I've printed several of these in ABS and TPU.  The ABS version secures with a more satisfying snap.Fully parametric FreeCAD file is included, so you can easily adapt it to your particular...

This developing tank allows for developing up to 120 feet of 16mm in one batch using minimal chemistry (estimated 750ml with a full batch). It can be printed on a 185mmX185mm print bed. I've made the pour/drain holes large enough for quick...

I printed this in SainSmart TPU, but ABS or other hard materials work pretty well too.

I printed this in SainSmart TPU, but ABS or other hard materials work pretty well too.

The classic problem with older film developing tanks like Jobo 2000 series or Plastimat arises when the retaining clip inevitably breaks. This crucial part is designed to prevent film spirals from sliding upwards during agitation, but once it's gone,...

So I designed and prototyped this rolling cage that allows me to process roll films in my standard stainless steel Nikor development tank (the size that fits 1 roll of 120 or 2 rolls of 35mm), without losing easy access to the lid. After some...

Developing 8 sheets of 4x5 film at a time. Print with PETCF for best performance. ... PLA is too crunchy PLA+/PETG/ABS are too soft ABS-CF should also work.

I shoot and home-develop a lot of different film formats, and after releasing a few different reels for lesser used formats (110, APS, disc), I started getting approached by people wanting one of equal quality for the Minox 8x11 subminiature format.

Developer and fixer saver for Paterson developing tank and it's reel - for 120 films. It saves about 100ml of the developer, fixer, etc. ... Idea taken from: https://www.thingiverse.com/thing:4300849

Developer and fixer saver for Paterson developing tank and it's reel - for 120 films. It saves about 100ml of the developer, fixer, etc. ... Invest in shell (use at least 4 layers/lines) Idea taken from: https://www.thingiverse.com/thing:4300849 ...

I shoot and home-develop a lot of different film formats, and after releasing a few different reels for lesser used formats (110, APS, disc, etc), I started getting approached by people wanting one of equal quality for the Minox 8x11 subminiature...

This is a cassette for the Minox (and others that use the same cassette) cameras. Print instructionsIt requires a 0.25 or smaller nozzle at .10mm DETAIL setting and thin wall detection.

I remixed the Minox Filmcutter V2 from cpmalek https://www.thingiverse.com/cpmalek/designs https://www.thingiverse.com/thing:3222458 The ‘Blade’ piece holds three double-sided razor blades The ‘Box’ piece covers the bottom of the blades and avoids...

Film Holder for Minox Spy Camera for Scanning with Nikon Coolscan 9000 or 8000

I bought quite a few broken beyond repair minox 35's and decded to take a couple apart to attach them to a leica body. You need the tiny screws from the minox that hold the lens on. ...No guarantees.