detolf funko 3d models
3660 3d models found related to detolf funko.
thingiverse
I designed the clips to add more shelves to Ikea Detolfs because they do not allow extra ones naturally. These clips consist of four pieces and permit one additional shelf each. Each pair is utilized to connect a horizontal rod to the vertical rods...
thingiverse
Glass support IKEA DETOLF for add glass and get more space :)
thingiverse
A Clip for the detolf vitrines for when the silicone tubes that hold the glass are defective. ...
prusaprinters
Mount for IKEA DETOLF additional UTRUSTA glass 30x37You need:8x M3 Nuts8x M3x12 Bolts
thingiverse
Display shelf that fits in IKEA Detolf cabinets. ...14.75" (373mm) wide X 3.25" (82.1mm) high X 10.5" (265mm) deep when fully assembled.
thingiverse
This part is used to soozafones Gunpla base to an IKEA Detolf glass display case and create aerial poses for your Gunpla. ...https://www.thingiverse.com/thing:2702736 Connector is friction fit, and can be combined with several of soonzafones arms to...
thingiverse
Are you struggling with an IKEA Detolf that has far too few shelves? ...If so, this clever solution is just what you need - it provides a simple way to add extra shelving space using A3-sized plywood panels, giving you the perfect non-transparent shelf...
thingiverse
I used these kits on my Detolf glass cases. The floor in my basement is a little unlevel and I had a low spot that just max out the adjustment on these feet. You print these and put the foot inside. The Engineering Gray was a very close match. ...
grabcad
Featuring a traditional Ikea glass display cabinet, this item is currently without certain elements such as the upright rods.
thingiverse
Mount 10mm wide bar for mounting LED tape on IKEA DETOLF
cults3d
Designed these to add different dimension and heights for the IKEA detolf shelf. Currently using them to display funkos on one shelf so it's multi-purpose. The action base fits snug into the stands and you can mix and match how you see fit. I've...
thingiverse
Clips to bend and hold Neonflex (from Bunnings in Australia) led light. ...Fits to Ikea Detolf glass display cabinet.
thingiverse
Lost the magnetic latch for your Ikea Detolf cabinet? ...Here's a non-magnetic replacement derived from ThijsOudeVrielink's door latch
thingiverse
Simple, screwless shelf support for the IKEA Detolf display cabinet. Print the support with flexible resin, tested with Formlabs Flexible 80A. ...Designed for light load.
cults3d
Brackets for adding new shelves to the Ikea DETOLF display case. The dimensions of the new glass panes would be 38x29.5 cm. ... The recommended screw is a DIN 912 4X12 allen head, with its corresponding nut.
cults3d
This clip is designed to be used with the standard nut and bolt on your Detolf display cabinet. Please be careful not to overtighten. ... Bolt hole diameter: 5ml Nut hole diameter: 8ml
thingiverse
I designed this creation because I couldn't find anything comparable online using a 3D printer and needed illumination on all shelves of my DETOLF. Hopefully, it will work for you. ... If someone wants to enhance the connection between the two pieces or...
thingiverse
In it I also suggested trimming A3 glass to make a shelf, and an additional half shelf (1/3 shelf actually), but some people have told me that these are actually a bit wobbly on their detolfs. These clips can be used to secure a half shelf more...
thingiverse
These are staples to hold led strips on the metal rods of the Ikea Detolf showcases, since with the double-sided tape that the strips come with they fall off over time. I recommend putting 3 in each section, that is, 24 staples per display case. ...
prusaprinters
These are staples to hold led strips on the metal rods of the Ikea Detolf showcases, since with the double-sided tape that the strips come with they fall off over time.I recommend putting 3 in each section, that is, 24 staples per display case.They...
thingiverse
It allows you to add extra shelves to the IKEA DETOLF display cabinet by clamping them to the side and then locking it in place with 2 M3 nuts and 2 M3 screws, each 12-15mm long. ... To make assembly easier, print 2 of these parts normally and 2 of...
thingiverse
The DETOLF is a fantastic piece of furniture that showcases a collection of glass objects to perfection, such as my exquisite salt cellars. However, it only comes equipped with three fixed shelves - four if you count the base. These shelf supports...
thingiverse
I also made a clip that attaches the 4.5mm cylindrical wires to the IKEA Detolf display case metal structure to neaten up the wires, which you can find here: https://www.thingiverse.com/thing:4962208. I made this on Tinkercad. ...You can make your...
thingiverse
IKEA Detolf Glass Shelf Holder. Note that there are left and right versions available. For one shelf, you must print two times the left version in addition to two times the right version. The cutout on top is designed to secure the position of the...
youmagine
Note that this makes it incompatible with the lowest shelf of the Detolf (which is not glass), although the design could be easily modified to remove the lip for that application. Instructions: 1) Adjust the SCAD file as needed to suit your...
thingiverse
These are clip-in spacers for the Ikea Detolf glass curio cabinet. They are designed to snap onto the metal vertical rails with no tools or fasteners needed and are sized to divide each shelf level in half (190mm / ~7.5in.) with no measuring...