desk riser blocks 3d models
124184 3d models found related to desk riser blocks.
thingiverse
Customized version of https://www.thingiverse.com/thing:4088666 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4088666
prusaprinters
... simple support for my desk calendar. ...The calendar sits below eye level so you are not able to see the month/date well. So a small angled block keeps the date/month up towards me without having to balance them every time the date/month changes :)
cults3d
The Desk Riser was designed to be printed by a CR 10 and so I couldn't print it with my Ender 3 V2 because the build plate is smaller. So I decided to cut it in half and put in these connectors. Remixed using TinkerCAD. ... This is the first remix I've...
thingiverse
The Desk Riser was designed to be printed by a CR 10 and so I couldn't print it with my Ender 3 V2 because the build plate is smaller. So I decided to cut it in half and put in these connectors. Remixed using TinkerCAD. ... This is the first remix...
thingiverse
This riser also allows me to store different sizes of papers underneath the plywood base and keep my SIS Ink setup, spare ink bottles and printer at my desire height. I share the "1 piece" version and "2 pieces version" for small printers, but you...
thingiverse
The Micro T1's riser block is a vital component of its overall architecture.
thingiverse
I decided to create a holder for the most widely used sizes of post-it blocks. I printed it with the "left" side facing downwards. The layer height was set at 0.2mm, the nozzle diameter was 0.3mm, and the infill density was 10%. This design comes in...
thingiverse
These desktop risers elevate your monitor about four inches off the surface. The wooden components you see are 5 by 3/4 by 24 inches in size, sourced from Rockler Woodworking. ...Following printing, I use an X-Acto knife to carefully trim excess...
thingiverse
This is a PC fan riser block I made for offsetting my 140mm Noctua fan on top of my PSU shroud.
prusaprinters
The height of the lift is just over 2 inches (~55mm). My desk had existing holes to screw the monitor stand down, so I modeled a peg onto the bottom of the riser to fit into these holes (0.3" (~7.5mm)). ...If your desk does not have holes, you...
thingiverse
I built an amazing collection of organizers especially for my wife's makeup box. ...They connect seamlessly with a simple snap, allowing us to print any component we desire and then easily assemble it in place.
thingiverse
You can always opt for a wheel-riser, but I'm the type who'd rather craft something with my own hands than shell out cash. So, I set out to build one from scratch. ... It should accommodate tires up to 1 1/4 inches (32c) diameter, though please keep in...
thingiverse
Modified Jerooney's model to work with a standard 11-3/4" x 5/8" (299mm x 16mm) shelf board from the hardware store. Also added a peg leg in the center as I cut my board to 45" and I did not want to see any future sagging. ... The end pieces are...
thingiverse
Remixed this nice Monitor stand to my needings. Thanks to: https://www.thingiverse.com/tomthrelfo as he published the stand i've remixed it from: https://www.thingiverse.com/thing:4276960 I've also added small holes to the stand so that you...
thingiverse
Built upon the remix by DanegerousT and made it perfectly fit my 15.6" Asus TUF Laptop. The spacing means the brackets sit right under the rubber bumpers on the base of the laptop. ...Really liked the dovetail crossbar design that DanegerousT made, this...
thingiverse
Overkill on material use? Certainly. Hexes? You got em. More hexes because you want to use honeycomb infill? Hell yeah. Uses the BURHULT Shelf from Ikea - white59x20 cm I've uploaded the original as seen in the photo - but the tolerances...
thingiverse
I am using these four blocks of PLA to raise my 55-inch LED TV by three inches so that I can fit my center speaker underneath it. That's been a game-changer, let me tell you! Thanks for your help and stay safe. ... By the way, Thingiverse isn't working...