desk clamp on shelf 3d models

This versatile clamp secures the edge of a desk with an additional attachment point that holds items upright. By utilizing this setup, I'm able to firmly fasten my control box to my standing desk after detaching it from its treadmill mount, freeing...

someone asked for a desk edge book clap on facebook. ... I was bored.

For 16 mm thick board The shelf holder can be mirrored in cura

I want to use a IKEA Lack shelf as a monitor and speaker stand on my desktop.. It's a bit too big for my CR-6 SE to print, so gonna make a split version also. Infil i will go for: 20-30% No support needed, just rotate the flat side against the...

Keep in mind I kept the dimensions for the top&bottom thickness, so stacking them results in a bit more plastic and thickness on the stacked shelf. ... In the future I want to add a back to allow wall mounting with double sided tape, and a way to...

The trouble being that I was unable to find a clamp for my desk lamp that was large enough for desk size. This clamp has been in use daily for about a month as hasn't moved a bit. As seen in the pictures its under quite a bit of stress and...

The clamp attaches to the back of your desk with a screw, pre-drilled hole for safety. Choose from LAYWOO-D3, black or brown plastic to match your desk. The slot in the middle allows wide cable acceptance. Adjust the size using the scad file as...

needed a short stant for the desk. ...85mm high 50mm square mount, 2 screw locations to mount and side screws for stability at the end of the desk. ...2 iterations

This versatile clip attaches neatly to shelves and desks, providing a convenient place to hang your backpack at an instant.

Went on sale for $20 and I jumped but upon getting it, discovered it was about an too deep thanks to a wing on the back to fit my desk so i decided to make my own which is an inch wider and half an inch deeper for storage than that was. It lacks...

then move the drawer and the clamps to your desk and take the clamps and press them against the pieces with little holes in them. This for the clamp contest. ...Look at picture if you are confused.1* body of drawer1* drawer of drawer4* clamp of drawer4*...

I designed my first 3D creation, a versatile desk clamp with an integrated hook, specifically for my wife to conveniently store her hair dryer. ...The design still requires some refinement, particularly in terms of the boot fitting snugly onto the bolt,...

This versatile desk clamp is designed to securely hold items ranging from headphones to smartphones in place with precision and stability. It prints effortlessly without any need for support materials. ...To ensure optimal results, simply orient the...

The unit is super convenient but has a pretty big footprint on the desk and because of the built in Qi charging pad, storing things on top isn't ideal. So a small table that fits over top the charger provides ample space for a Stream Deck and...

... drill it a bit. Log * 30.5.2021 - Releasing Vise mk1. * 30.6.2021 - Started working on new Rod + ThreadModule with higher pitch. <br> * 1.7.2021 - Added assemble video. * 1.7.2021 - Added Slider_clamp_V2 for higher clamp pitch. ...<br> </p>

This customizable desk clamp securely holds a wide range of items from headphones to cell phones in place.\r\n\r\nPrints without the need for support, allowing everything to lay flat. To ensure proper orientation, make sure the logo faces downwards...

### New response: This desk clamp is designed to hold a PCB, inspired by Lady Ada's tool in her instructions. It requires more super glue than expected but functions well after printing. The base is small, causing instability, so improvements...

The tabs on the side panels and the holes on the back panel may need slight filing/drilling to achieve a good fit. Everything else I had to print one at a time. The box took 15 and a half hours to print at 50mm/s. I have glued everything with...

I was on the lookout for a reliable iPhone holder to perch on my desk, and this particular model has exceeded all of my expectations so far.

This is a clamp stand for a generic desk lamp. ========================== Required materials include M8 threaded rod, M8 nut, and Filament. How to Make it --------------- 1. Bend the M8 rod at a 90-degree angle. To do this, secure the rod in a...

These are DIY hooks for hanging leads and oscilloscope probes that I created since my desk already has pins for additional shelves. ...Perhaps others may find them helpful as well in the future.

Under desk caliper storage, I got tired of moving my calipers every time I needed to do something, so I made this to get them out of the way.

Under desk caliper storage, I got tired of moving my calipers every time I needed to do something, so I made this to get them out of the way.

To execute my plan, launch openSCAD and adjust the variables according to your desk setup. Most Luxo lamps have a 60mm diameter mounting rod, but feel free to customize. After printing, add padding to the upper clamp base and the screw's top bracing...

The earbud magnet clamps securely onto 1-inch thick desks with ease. Its robust design features a 50mm x 15mm x 26mm magnet that provides unwavering support for your earbuds. Crafted using OpenSCAD, this innovative holder is built to last. Print...

... for the plywood size which can be edited and the models will automatically adjust. ...Screws used for plywood and for attaching stacked shelves are #2 sheet metal screws and I would recommend ½" countersunk screws. 5 screws are used per shelf support.

Constraints: * The desk must be less than 60 mm thick * The clamped object must be shorter than 60 mm * Several kilos can be supported with only 15% infill Notes: The rotate shaft is printed at a precise 9.85 mm thickness. If the clamp appears to be...

I had a problem with power boards moving or falling off the edge of tables when I move things around.This clamp holds a power board at the edge of a workbench, table or desk. It uses the mounting holes that most power boards have.&nbsp;To align the...

I decided to design it myself by reducing the printing time. You will need : Aluminum tubes 10 mm in diameter Plexiglass or printed plates (not included) Prints : "etagere" file must be printed 2 times : it is used for the bottom and optional...

This is a Remix of https://www.thingiverse.com/thing:3468079 I loved the thread design of the original but it was not big enough to fit the thickness of my desk as I have a metal arm that stabilizes the desk legs. I made the following adjustments to...