desk clamp on shelf 3d models

A small shelf, nothing special. Easy and fast printing. ...I am using a wifi repeater</p><p>0.2mm layer height<br>20% infill<br>3 perimeters<br>&nbsp;</p>

... a diameter of 16 mm. To secure this support to the shelf, you can use M3x30 bolts and add a few strategically placed knots for added stability. I'm also adding a clever tip to the bar to make it even more functional. ...Enjoy your new spool holder!

I'm looking for a phone stand that clips onto a shelf, but it seems they're not available. So, I decide to get creative and make my own using Goralski's tablecloth clip as the starting point. Thanks, Goralski! ...With some simple modifications made...

I created the MasterKey Rails since there were no free clamp-on options available on Thingiverse. The rails are now available in 3 sizes: 1", 3", and 4.25". You will need two clamps and one base to complete the setup. I designed the clamps...

A Remix of Andrew Godfrey's Soldering Clamp found on Thingiverse - I just made the base wider for more stability and added 4mm to the bottom to raise it slightly.

This design introduces a straightforward snap-on handrail clamp that serves as a foundation for various attachment techniques. Its innovative diamond pattern is 3D printable and lightweight, though customizable or removable if desired. ... Best regards,...

I have printed it standing and lying on its side with no noticeable impact on the threads. I have included two different screws for the clamp. One is just a screw with a flat top, and the other has a ball and socket joint pad to protect the underside...

I have printed it standing and lying on its side with no noticeable impact on the threads.&nbsp; &nbsp; &nbsp;I have included two different screws for the clamp. One is just a screw with a flat top, and the other has a ball and socket joint pad to...

A simple cable tidy to clip on the back of desks to prevent cables falling behind the desk when they are unplugged. There are two sizes: small will fit normal 15mm 'melamine' top desks and the large will fit thicker 25mm desk tops. ... ...

Many people like my original hand mic mount, but some folks wanted something that would clamp onto a thicker surface, and I wanted to make some refinements, so here's version 2 of the clamp on hand mic holder for CB and amateur radio.I recommend...

Wanted replacement tips for the small and large spring clamps that I have, so made this remix to create a snap-on option. ... Found that printing them upright with supports made it relatively easy to remove the support without breaking the part that...

I quickly designed a clamp-on light base using Fusion 360 in just five minutes. ...I measured the dimensions from a partially intact piece and recreated them exactly, making sure the new design looked identical to the original while still functioning...

A custom-designed holder is needed to accommodate a rechargeable flashlight that runs on a high-capacity 26650 lithium-ion battery. ...The precise dimensions required are a diameter of 33 millimeters and a total length of 140 millimeters.

I took the dimensions off a piece that wasn't completely shattered, and I made it look as similar to the original as possible, while maintaining functionality. Print instructionsUnassociated tags: clamp light, clamp light base, simple print Category:...

I didn't fancy chasing the ER11 around to ensure the touch plate is always under the cutter, so I came up with this Clamp On Probe. It clamps on where the spanner goes on the ER11, so it pretty much sits in the same position every time. I designed...

Requirements - 1 bearing 608 (608z, 608zz) - 1 wood screw 20x4 or longer (depends on your desk thickness) Print desk-draw and desk-draw-knob parts and optionally the desk-draw-washer. Assembly: Place the bearing in draw-desk until the surface of the...

you can remix it to attatch things to it

The way this suppressor fits onto the barrel is that you slide this on the barrel all the way and make sure it is fitting snug. Use an M5 nut and bolt to tighten the suppressor to the barrel. The top of the suppressor forms a clamp that holds the...

I've crafted these clips so I can finally impose order on the cables that keep dangling from my desk. I'm aware that this product is geared towards a very niche audience, as most people have their own desks. ...These clips attach securely to the metal...

I needed a convenient place to hang my headphones, and I have desk-clamp tripod rods attached to my sit-stand desk, holding up lights and a camera. So I decided to put this together. You will need a nut and bolt to clamp this to your tripod rod. ... ...

It's Mainly Designed For Geeetech Single Extruder Style Printers, But Can Also Be Used For Mounting On Any Stepper Motor For Cable Management Purposes. For My Setup, I Added An Extra Platform To Attach My Led Array, But Unfortunately, It Kept...

Added a nut insert and remade the nylon thread insert (easier to print and better to mount the poster on the wall). Add a few millimeters extra to your poster length (5mm is a good value). Print with higher infill for added weight if your...

I've been looking for a new headphone stand - I couldn't find one I liked, so I decided to make my own in Solidworks!It's mounted via a screw to a desk to clamp it down.You shouldn't need supports for the, but if needed, supports for the support rods...

This is a customizable clip based on your snap-in flashlight clip, designed specifically for attaching a small flashlight to your hardhat to use as a headlamp. Two sturdy screws clamp the clip securely to the brim of a hardhat, providing a rock-solid...

The clamp is the original one, https://www.thingiverse.com/thing:3087628 The screw is my shortened model https://www.thingiverse.com/thing:4793780

A clamp-on cupholder designed to fit a 2" outside diameter. Requires: 2x 3/8-16 x 1.5" SHCS https://www.mcmaster.com/91251A628/ 2x 3/8-16 Nut https://www.mcmaster.com/95479a118 Should not require supports to print. Due to size of the cupholder,...

... T-table firmly in place by clamping it down. ...Secure the clamp with a reliable hold, requiring six M6 screws equipped with T-nuts for optimal stability. ...The T-table was manufactured with Fiber Force filament, ensuring its strength and durability.

Antenna (or any project) holder perfect for clamping to a deck or railing. Designed around 1/2in pvc conduit but should fit anything around that size due to the tapered hole. ...Use the screws and pad from thing:2767847

Antenna (or any project) holder perfect for clamping to a deck or railing. Designed around 1/2in pvc conduit but should fit anything around that size due to the tapered hole. ...Use the screws and pad from thing:2767847

I had an old clamp-on lamp just like the one shown in the picture, so I decided to give it a new life as a magnifying lamp. The lamp has been designed for a 100mm magnifying glass, a small C&K toggle switch, a 12V LED strip, and a 12V adapter as its...