delta 12 compound twinlaser miter saw model 36255l zero clearance insert

As a learning exercise I designed and printed this insert for my Delta miter saw. It fits really well, I only slightly had to drill out the small holes, but otherwise it fits like a glove. I printed this in PLA, 0.2mm layer height, 50% infill. The...

As a learning exercise I designed and printed this insert for my Delta miter saw. It fits really well, I only slightly had to drill out the small holes, but otherwise it fits like a glove. I printed this in PLA, 0.2mm layer height, 50% infill. The...

Delta 12" miter saw insert plate for Model 36-255L (might fit others) Uploading two different options. One is smooth on both sides. The other has "indents" on the bottom similar to the original throat insert plate. If you print the one without...

This is a design for a replacement insert for a DELTA 36-220 10-Inch Compound Miter saw. Print it with a fairly high infill, no support required, then screw it into the saw and with the saw running slowly lower the blade to cut the groove. ... ...

This is a plan for a substitute part that fits a DELTA 36-220 10-Inch Compound Miter Saw. ...Print it out using a moderate to high level of infill, as no supports will be needed, then screw this insert into place while the saw is running at a slow speed...

Dewalt DW705 Compound Miter Saw Zero Clearance Insert. May fit other similar saws Fits snug, flush. I included the Prusa Slicer Project file. I added a modifier to the center area to ensure it was solid in the cut-through area. Printed with PETG ...

I upgraded the standard stock insert on my DW715 Dewalt Miter saw with a custom-made zero clearance insert. After several months of use, it still looks like new and shows no signs of wear or damage. ...The design is compatible with a long bed 3D...

Zero clearance insert for the Dewalt DWS780 miter saw made with Fusion 360. I printed mine on a CR10 V2. ...Since the part is so big, I had to orient it vertical and at a slight angle to make it fit the buildplate.

I designed a zero-clearance insert to replace the standard stock insert on my DW715 Dewalt Miter saw. After several months of use, it still looks almost brand new with no significant signs of wear. The only caveat is that it needs a long bed, which I...

I created a zero clearance insert to replace the standard stock insert on my DW715 Dewalt Miter saw. This one has been in use for a few months now and doesn't show any serious signs of wear. ...It requires a long bed (I have a prusa i3), but it it could...

This is a zero clearance insert for Dewalt miter saws.I modeled it from the insert on my own saw wich is a DW716 (12inch, dual bevel, NON sliding)from what I can tell from the replacement inserts on amazon, this will fit...

Zero Clearance Insert for the Hitachi 10FCH2 Saw (Should also match the Metobo C10FCH2). Works fantastic, just needs some minor adjustment to avoid sanding to install. I will fix the fit just a bit in the next revision I produce. ...For now, if you...

Zero clearance insert for a Ryobi TS1345L. Should work with anything in the 1345 line (the L is the refurb model). Uses the screws from the existing throat plate. Once it was installed, I cut the slot with multiple small cuts. The PLA melted...

Zero Clearance Insert for DeWalt 12" Compound Miter Saw, Model DW715. I attempted to re-create the original as much as possible. It is not a tight fit, but neither was the original. After installation, run the saw through the insert to create a...

Dewalt Miter Saw DW703 Zero Clearance insert splited on 2 pieces to be printed on small printing bed. Bead and cove design to insure both parts stays in place once bolted to the saw base.Print face down.Slot is thinner than the saw kerf. ...Just bolt...

This is an insert for the Ryobi 10" sliding compound miter saw model TSS102L. This is **not** actually the zero clearance insert itself - this is a base that *holds* an easily-replaceable ~1/4" thick insert of size 1" W x 14-1/8" L x 5.16mm T. I'd...

Made this insert to fit my Dewalt DCS361 miter saw. ...See print settings below.

Zero clearance inset / throat plate for Craftsman miter saw (model 137.212290). Bought the saw used and the throat plate was cracked and falling apart. I taped up the remnants and modeled a new one since these are impossible to find. Print with...

... ...I created a zero-clearance insert that perfectly matches these specifications. The model was printed with PETG filament, but it should also work well with PLA. ...Please note that this design might not be compatible with other Einhell models.

As many Einhell tools they use non standard shape, so I wanted a zero clearance insert and here is.I printed on PETG, but works on PLA too.I don't know if works for others Einhell models.Print SettingsPrinter:Rafts: NoSupports:NoInfill: 20  Category:...

Customizable zero-clearance throat plate designed specifically for Craftsman miter saws, model number 113.235120. ... Made using DLP technology and requires #10 flathead screws for assembly.

I printed mine at 100% infill. ...Then I used CA glue right before screwing it down. Once I screwed down the insert, I made the cut.

Perpetual, replaceable zero-clearance for most models of the Dewalt miter saw. Printed in PLA (other matrials, such as PETG or ABS may work better long-term) with a slip-in, slip-out, 3MM PLA insert for all blade kerfs and settings. Tear-out is now a...

This can be used to create a zero clearance insert, or a dado stack insert, or an angled zero clearance insert. This is fully customizable for any table saw that has an oval shaped insert by simply changing the measurements. I usually make these out...

I built this for a colleague; Replacement Craftsman 12" Compound Miter saw grip. The previous grip snapped off, so I simply tapped this grip into position with a little force. Glue may hold it even better, but the fit is already very solid by itself....

I'm just starting out with Fusion 360, but this project turned out surprisingly well, so I've decided to share it with you. The print was done in Overture Yellow PETG, which looks incredibly similar to Dewalt Yellow - a very satisfying color match.

This model provides a replacement for a broken or missing motor cover on a Delta Compound Miter Saw. It works on model 36-075 and possibly others with similar shaped motor.I own this miter saw, and many years ago I broke off the plastic motor cover.

Compound Miter Saw model, finished about 30 min ago.

This is a zero clearance insert for the Delta 36-725 Table saw. I cut it from 3/4" plywood. It could potentially be 3d printed as well - some minor sanding was required for perfect fit. I did not model a cutout for the shaft housing, so when you...

A quick replacement of the stock zero clearance insert on the WEN 3959 benchtop band saw. Stock photo shows the gap it leaves, which allows small cut offs to fall in. This new insert also reduces tear-out. ...I printed at 50% infill with tree supports...