deep one 3d models

Due to student usage in the day time, only one of the printer is avalaible. Thus we made the decision to assemble the structure in Solidworks and scale it by 55% for printing in 4 blocks. This resulted in the loss of some minute details in the model...

However if you have any issue with the label to clip on the cap just scale the label in the slicer by a few percent in x/y direction and you should be fine.Standard VersionPhased VersionFilament Grabbing Mechanism How to UseTo clip on the label,...

In the event of a driver failure, only one bank of LEDs will be effected while the other banks will continue to operate. In the event that of an LED failure, the mating LED will continue to operate.The EPL-HB-100LED-RT-UVA uses ultraviolet LED light...

The inlays (covers) can best be fixed in the letters with a few dots of glue if they appear a little loose due to the tolerances.For the LED strip, I recommend the one from Action (you need a little less than 3 meters for this model). I got LED...

If you are struggling to print the whole version in one go but don't want to use the segmented version (less clean looking) it's also possible to 'slice' it into two pieces in your slicer of choice and use TPU welding to put the two pieces...

A little over 1 gram of filament is enough for one division! A good way to join two pieces together is to take the first piece (label facing you) in the left hand and the second piece (with the label up) in the right hand. Attach to each other. The...

My original “Motorized” design also used two motors; one to turn the Carriage, and the other to drive the clock Hands. I never posted it because I wasn’t able to get the code to reliably display the correct time with the Hands stepper, after you...

Actually, if only using 7mm thick ones, you can easily fit 6, but this was designed taking into account old computer cases that need this many drives are likely low end NAS boxes, so space was left for beefier 2.5" drives up to 15mm thick (aka the...

The inlays (covers) can best be fixed in the letters with a few dots of glue if they appear a little loose due to the tolerances.For the LED strip, I recommend the one from Action (you need a little less than 3 meters for this model). I got LED...

Finally, note that most tiles will have a round symbol display added to one edge (see image gallery). This display will feature either an arrow, a triple arrow, a foot stepping on spikes or an eye. These symbols corresponds to the "ordinary room",...

If one segment is 0.5mm too short, you can adjust the gap to 1mm to achieve the right dimensions for the overall panel. E: Grid/noGrid: Segments with an optional Grid that increases their general strength (see pictures) Currently there are...

Instructions: ---------------- - **Strip USB cable** Cut one end off your USB. I left quite a bit of cable as I am not the best at stripping cables so I wanted space in case I needed to redo it. You can cut it much shorter if you are comfortable. -...

The basic idea is a fairly simple one, and not new, but I hope all will agree this take on the idea is very well implemented: -Take a modern LCD panel and driver board -Mount it inside a suitable box -Use that either as a nifty little monitor or as...

Update 7/29/2022: Updated the covers with ones that are less noisy. Like my work? Post a make! Print Settings Printer: FLSUN SuperRacer Rafts: Doesn't Matter Supports: Yes Resolution: .2 mm or .3 mm Infill: 30 Filament: eSun PLA+ Purple Notes: ...

As one mesh and divided into parts. Animated FBX files included. ... Animations General MECANIM T-Pose: 0 - 0 fr., S_IDLE: 2 - 100 fr., S_sit_down: 101 - 126 fr., S_Sitting: 127 - 177 fr., S_Sitinhg_Talking_A: 178 - 313 fr., S_Came_up: 314 - 340 fr.,...

Add manual relations to make the diagonal part of the smile parallel. Draw a 3 point arc connecting the outside and inside edge of the smile at the topSmart dimension the bottom most point of the smile to be the specified dimension from the very...

You can use one of the M5 screws from old Z axis wheels. Then just mount to the 4040 extrusion.MGN12 mount - For this mount you will need the belt ready to be attached (so you'll need the motor mount on first). Put the part in place and figure out...

As well as all the hardware is arranged to give support to the pieces and act as a lock on certain bearings (the 20 mm ones lock inside the clamps with the screws). The threaded rods that I use to transfer the movement of the motors are common 8...

Use a light or clear/translucent filament for the diffuser (if you are using one). Code The code (.ino) for this project is configured for a 12 LED NeoPixel Ring. It randomly fades 6 LEDs in and out, using green, blue and pink colors. If you are...

The inlays (covers) can best be fixed in the letters with a few dots of glue if they appear a little loose due to the tolerances.For the LED strip, I recommend the one from Action (you need a little less than 3 meters for this model). I got LED...

Gerne ein Herz vergeben und/ oder mich in den Favoriten speichern. English translation:“JOAN” as a printable LED name lamp.I work in child and youth welfare and also use this hobby to make LED lamps for all the children in our care to give them as...

Using the start-up guide you can program the ESP8266 with a browser-based interface https://install.wled.me/ and do everything else using the App.https://kno.wled.ge/basics/getting-started/The App allows you to createsegments to group all LEDs in a...

The Hyperion is one of the smallest and slimmest cases to date for your DIY SlimeVR Trackers. With its completely tool-less design and tolerances fine tuned specifically for FDM 3D Printers, the Hyperion is both easy to print and assemble! Every...

There are also alternative cover plates for without any sensor and one with an offset down stand potentially for a LED light source and wiring. The firmware changes were relatively simple, there are only a few comments to tweak. I did however have...

References for mobo specifications, standoff locations and screw specs: https://en.wikipedia.org/wiki/MicroATX https://en.wikipedia.org/wiki/ATX#Variants https://en.wikipedia.org/wiki/Computer_case_screws...

 Get that wrong, and you WILL burn out your MagicBand+, as there is no reverse-polarity protection circuit. I recommend a digital multimeter to test your leads before you run power, if you want to make sure you've got the polarity right...

This is a remix of Max Kern's great ZeroBot robot (more on Hackaday.io), with the following changes:HeadlightsGrooved tiresCharging portFront panel holder.Also, thank you Kelly Jordan for the inspiration with your aggressive tank tread.Some extra...

In addition, the holes for the M2 screws were slightly reduced on one side (variant A). For variant B, 2 completely new nacelle halves were created.</li></ol><p><i><strong>Attention! Electricity is dangerous!</strong></i><br><i><strong>Reconstruction...

Better use my experience and create something of your own, lighter =) If you are interested in a solar panel, then I would recommend using this controller - http://alii.pub/5xa8ac And these are the solar cells - http://alii.pub/5xa7ns They are not...

(2) BEAR BOWDEN EXTRUDER: Print the Bear extruder, hone the filament hole with a 2mm drill bit (or larger if you plan to line it with PTFE, print the Bear Bowden lid that I've designed, get yourself one of those Creality Metal Bowden kits with a...