decoy wasp nest 3d models

...  In the horrible rat's nest of OpenSCAD code I've written, there's an option to make the bridge and nut higher or shorter.  If these work reasonably well, I'll work on making them better.  But, for now, I just wanted to publish SOMETHING to share.

The spacer is inserted barrel first and nests inside the barrel/breach portion and gives the shorts shells the correct surface to butt up to so that they can be used. You need to fit an O-ring in one of the groves to stop the spacer sliding out of...

The Stand -off Spacers provide the Rubber Band Seal some space.I prefer the filament to exit out the bottom of the dry box instead of the lid, so I drilled a hole in the bottom and put the plug in the lid hole.SpoolsBoth the spool and filament guide...

Some plant options you might consider include: * Bromeliads * Ferns * Devil's ivy * Succulent plants * Dracaena * Sea thrift * Bird's-nest fern * Moses-in-the-cradle * Stephanotis floribunda * Phlebodium aureum * Pteris cretica * Davallia fejeensis...

It can be fitted with a full machine gun nest, for local defence, and is designed to be modular for easy repair in the field. This is work in progress - I am printing approximately widdth 60mm/ length 140mm/ Height 45mm as a 1/72 model (to...

I wanted to build a storage shelf for heavy loads using PVC pipes, thinking three tubes nested inside each other (16, 20, and 25 mm diameters) would make the whole thing rigid enough. Unfortunately, this isn't the case, but it's already good for a...

I deliberately varied the segment sizes to prevent misassembly and to facilitate nesting if desired. All four pieces can easily fit on a 200mm square bed. I recommend using the complete 127T gear for convenience when switching between metric and...

This is an easy-to-print Synthesizer Stand for LYRA-8 Organismic SynthesizerWill support the LYRA-8 Organismic Synthesizer or Synthesizers around 266.7MM X 266.7MM or 10.5 inches x 10.5 inchesPlaces the Synth on a comfortable 5 degree slopeNo support...

For a realistic display experience, each component nests into its counterpart perfectly, so I adjusted my original design to minimize size - just be aware that this makes the finished product slightly shorter than the actual Falcon Heavy. Upon...

Crows nest in forward of ship has parts too small (Railing). Causes warping due to the hot end being too close to print for too much extended time. Might be okay if direct cooling was applied. Best to remove them anyhow. DISCLAIMER I do not own...

First, one with a similar structure to omicron22's, where the silver part nests into a tray with raised black edges that are nearly as tall as the silver face with a similar contour. The edges of the silver arrowhead are rounded so that the black...

The winding mechanism incorporates a nested planetary gear, allowing the clock to continue running while being wound up. Every component of the clock is 3D printed, except for a few small screws, metal pins, the cord, and the lead for the weight. To...

TRANSFORMERS Studio Series Grimlock 86 Upgrade Kit Pés Nosso kit de peças de Upgrade para o Transformers Studio Series Grimlock 86 Upgrade Kit Pés Neste post apresentamos kit dos pés quefoi impresso em ABS e testado em um Action Transformers Studio...

Modern shopping carts are predominantly made of metal or a combination of metal and plastic, designed for easy nesting within each other and space-saving storage. They come in various sizes, including some that can accommodate children. Specialized...

Model cost 3 drawcall and 4 batch, body of lamp, glass exterior, glass interior and flame Model use 3 different shader: for body need PBR alpha test, for glass shader with transmissive, refraction and emissive, flame with emissive and transmissive 9...

You can watch pieces printing here: https://video.nest.com/live/ZtxS4shYdv. I'm still printing and need to model helmet and backpack but legs all work fine as does head. Arms and hands still need testing but will keep this updated until done. I've...

The usual way to centrifuge a 0.5 mL tube is to nest it inside a 1.5 mL tube, but I sometimes had catastrophic failures when centrifuging samples for long periods at high speeds; the smaller tube would twist inside the larger tube, its rim would get...

Crow's nest and support pieces need to be placed with the up pointing part touching down on the surface - much like how anchors rest. Special attention is needed for printing capstan: this part needs to be placed upside-down for an error-free...

Place the detonator in the mine nest. 4. Screw the fuse back into the mine body. 5. Replace the safety cap on the fuse. 6. Set the mine in the hole or on the surface. Neutralization or Destruction: 1. Install a safety cap on the fuse. 2. Remove the...

Unit.Bins are a collection of storage trays that neatly nest and stack together. The outside edges of one unit measure 45mm x 45mm. Regular height bins stand at 12mm tall, while full height bins reach 24mm tall. You can place two 1x1 Unit.Bins on...

I'm developing a modular vertical kit formicarium, also known as an ants' nest. My ongoing research project is aimed at finding the perfect design for these complex structures. You can now purchase additional kits in my Etsy shop, which has just...

 I only built my own because I wanted more of a pointed end so that it can sit flat through the silica beads in the bottom of the box and not have to try and "nest" through them using a more normal flat bottom.  I also wanted a spindle with a more...

There are now two large drawers, and they are now deeper by 160MM; which will have them end on the other side of the next 2040 aluminum v-slot, nesting up to the power supply. 4) 120MM deeper, with back support bar. Smaller drawer is now on top. But...

There's a lip at the top and a recess on the bottom so you can nest two of these on top of each other for that situation. Does this fit into the rectangular shadow on the board where the player card stack usually goes? No, move it a bit closer to...

The original design of the cab included the mast and crow's nest, but it lacked structural integrity. As a result, I decided to print the mast separately (in pink) and glue it into place. One piece that is not included with this model is the pin...

(Subscribers get 50% off our entire MyMiniFactory store!) APL (Average Party Level): 9-11 --------------------------------------------------------------------- Tourist Terror Captain Scrupe, a tiltik goblin tour guide has run into a bit of trouble…...

With this crib, create a cozy nest for the baby to facilitate sweet dreams. Designed with star motifs, this wooden bed follows your child through nap time and bedtime hours. Furthermore, ensure baby stays warm by comfortably sitting in this lovely...

Put the checkmark in the box nest to the STL file you want to print and click the Print with 3DHubs button.This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:*Layer Height 0.1mm is recommended for a...

#Brick List |Sound|Brick ID| |-|-| |A - Airplane|01| |N - Nest|01| |B - Bear|02| |O - Otter|02| |C - Cat|03| |X - X-Ray Fish|03| |D - Doll|04| |Q - Quilt|04| |E - Egg|05| |R - Rainbow|05| |F - Flower|06| |T - Turtle|06| |G - Gift|07| |Y - Yo-Yo|07|...

Much better than the rats nest I had originally. Plenty of ventilation available and room for wire wraps to enter on the left side.</p> <p>Required: You will also need to print 4 of the simple standoff spaces included so the board doesn't sit...