ddlc 3d models

The models in my pictures were printed in beige ABS, which is a standard 1.75 mm filament from XYZ manufacturer. I have not tested other filament materials with this design. If printing as a fake sprinkler, I would recommend choosing black; bright...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

This is a vase with an Adafruit Neopixel LED ring modeled on the INTERIOR of the vase. Hidden away! It magically shows the light when you plug it in. This is a moderately advanced project. You'll not only be using your printing skills but also some...

*** UPDATE 30/06/2021 *** As lots of people have noticed, the original model is a ridiculous reducer at a ratio of about 3:1 from the original duct. I've now added a design that is much larger (labelled as "Full Size") and can be printed in three...

…unless you got yourself a special edition of a bobby car like a Porsche, Mercedes or the older Audi, VW or BMW models like I got. At most of the special edition you can’t fit the original push bar. I found the design of Klein-laui on thingiverse...

I recommend using a shorter heat sink and/or a fanBe sure to choose a fan size that will not interfere with the height of your heat sinkFilament sensor fits without issueBondtech extruder fits without issueOnly other fitment issues I have heard have...

Each knuckle is 35mm in length, axis to axis. As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the...

I already had some Koss Porta Pros so I printed it and used that for a couple of weeks (after tweaking the size of some parts for a tighter fit, especially the push pin which is/was modelled too small). However, after a couple of weeks using that,...

My O scale model train layout represents the section of the Pittsburgh & Lake Erie Railroad between McKees Rocks and Youngstown. This wall section (stretcher bond brick pattern) will let you assemble a background flat of the McKees Rocks...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

A remix to iTrooper's version https://www.thingiverse.com/thing:707734 Update 03.07.2022Models updated with new dimensions that is close to FreeTrack's suggested hardware dimensions.Only difference is the distance between the two front LEDs (82mm...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

-Number of facets causes extreme delay in saving/rendering model, likely due to me not understanding the correct scad approach; I am still learning, feel free to leave me any feedback so I can improve my techniques. -Flat ring design (just like the...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

Until very recently, I never got around to actually writing any documentation describing this idea or doing any model of this bearing concept. I only toyed with the concept in my mind for a while back then and put it on the back burner until...

I found models of the servo, Sharpie, and 28BYJ-48 stepper motor on GrabCAD, but didn't include them in the Fusion 360 assembly file here. The build log for my printer can be viewed here: https://openbuilds.com/builds/a-rolling-plotter.9207/ ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

https://www.printables.com/de/model/172064-phaetus-taichi-mount-and-fanduct-w-dual-5015-fans- ________________________________________________________________________ This is an highly integrated Mount and FanDuct for the upcoming Phaetus TaiChi...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be omitted on the inside. These connectors are specifically designed...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models) The small size and wide input voltage range of this unit make it ideal for operating Larson Electronics LED light bars, Golights and other equipment that requires 12VDC current...

While some complained about the expenses both in development of such tecnologies,a nd its application on the mech, the Fronc goverment applacate such concerns with the generous loan from the Alliance members.Gone is the troubling Andora-made gyro,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...