dd5e character sheet 3d models

EasyEda Picaxe schematic and board: https://easyeda.com/Rick100/ir_picaxe EasyEda Attiny85 schematic and board: https://easyeda.com/Rick100/attiny85-ir_motor_copy 50MM Clear globe:...

Stuff to print: 1 Diffuser (the big star-shaped part that transfers air from the impeller into the volute) 1 Volute (the snail-shaped thing) 1 nozzle (straight or 90 degree, your choice) 1 inlet bell (tall or short -- tall is best if you use one of...

If you want to save/backup it - click on "Read" and "save as" - save your backup somewhere. --Then switch from "device memory" to "open file" and point to the firmware bin file (or point to your firmware compiled from the sources).  --Click on...

It can also be used for accurate marking of other sheet material. Several sample STL files are provided but this script is really intended to be customized to your needs. Main features: * Metric, decimal inch, or fractional inch rulers *...

Drive system 3x Nema 14 motors 1.0A type 3x 16t 5mm shaft drive pulleys 3x flanged idler gears 6xm3 nyloc nuts 6xm3 A2 washers 1.8m of gt2 belt 3 printed carriages 1 printed effector 6x arms (either RC car rod ends traxxas or similar plus threaded...

because I wanted to and I had a lot of fun doing it :-). I tried to achieve the following key features: Easy to print without support (no steep overhangs or long bridges and stuff). Top and bottom layer printable on print surface (so I could make...

I used a white led strip but an individually addressable RGB led strip is going to be fitted and I will update the guide once it's finished.Materials need:chipboard (2 cm thick enough to cut out 2 circles with a diameter of 500 mm) or one sheet of 4...

To adjust the gap, turn the faceted knob, send the printer home and control the gap with a sheet of office paper. Clockwise rotation of the faceted handle corresponds to an increase in the gap, clockwise rotation - to a decrease in the gap. One full...

A set of printed components to build a robot arm that can be controlled and managed by any of the Raspberry Pi single board computers (SBCs),  This robot arm project with Python software and documentation, available from here, developed for the...

assembly requires a bit of soldering and patience for debugging :-)I used spare parts that I found at home, but these are easily available in any e-shop with Arduino-like electronics.Print instructionsGlowing platePrint glowing_plate drawing side...

i guess for the show and tell you could pass an object around and have the students measure it with the various tools then they could fill out an answer sheet and be graded on accuracy. for the full scale of the project you could give a grade based...

I ended up using #6x3/8in sheet metal screws, and a couple #6x1/2in for the side attachment. Narrow computer fan screws (with blunt ends and very coarse threads made for cutting their own threads in plastic) 1cm-long and 3mm diameter would be ideal...

lol", lady nylons and epoxy, masking tape and paint, thin tpu, newspaper glue and paint, rice paper, fiberglass sheeting.... yea.... I'm just gonna focus on making the landing gear today. lol the plan for landing gear is relatively simple as i want...

If there are bubbles visible in the bottle even though the vat is filled, there must be an air leak in the system and disaster can be avoided. To use the mod, print all parts in the following materials: Cap, Dock, Duct: Transparent standard resin (Do...

You could skip this and build it rats-nest style.220x150mmx0.5mm aluminium sheet. The thickness is not critical, but 0.5mm is easy to work with.200mm velcro battery strap: from HobbyKingOptionally, a little strip of velcro to anchor the battery tray...

Your other options are PET tape or PEI sheets with an adhesive coating between the sheet and the steel shim. Steel shim link: https://www.mcmaster.com/steel-shim-stock/shim-stock-6/ Instructions on sizing this are further down in the assembly...

Smooth sheet required for tight fitment of front and rear housings and strong bed adhesion.Cap: Standard version of the cap to hold the LED channels in place. File comes in the correct orientation for printing. Brim required for printing. Use with...

Incendia, along with her 4 followers comes on a diorama, with premade holes for 3mm Magnets, so you can switch all 5 characters between the diorama, and different bases.Queen Incendia fits on a 60mm base.Ash'kahn and Ignikash fit on a 40mm...

In order to conceal the places where the assembly parts are connected, the model cut along the contour of Spider-Man's body and the diorama's design elements. For you to achieve the cleanest 3D printed result, the character's head, limbs, hands,...

The figurine’s anatomy and proportions were thoroughly reviewed during the moderation process for the character and her clothes to be depicted harmoniously in the intended pose.The model’s cutting was chosen by our team to minimise the amount of...

ABOUT THIS 3D FIGURINEMeet the 3D printing model of Durotan – the chieftain of Frostwolf inspired by the character from the 2016 Warcraft movie which that was based on the popular WoW video game series, one of the today’s most famous RPGs. Though he...

HISTORY OF GWENPOOLGwenpool is a girl from a universe similar to ours, where all the superheroes and villains with superhuman abilities are just fictional characters one can find on the comic book’s pages. The reasons being unknown Gwen and her...

Both figurines' anatomy and proportions were thoroughly reviewed during the moderation process for the characters to look harmonically and in proportion in a diorama.The model’s cutting was chosen by our team to ensure the cleanest 3D printed result...

ABOUT THIS 3D FIGURINEThe Lord of the Rings movie trilogy based on Tolkien's legendarium gifted the fans a plethora of unforgettable characters, villains and heroes alike. Despite knowing every scene by heart, we still hold our breath rooting for the...

Just refile it a bit with a cutter!Update 31/01/24I started the electronic part with some late.The main issue is my board (NodeMCU esp32 or esp8266 d1mini)Both have some high deep sleep current, almost 20mAh, so running it on battery is pretty...

The in-game character is known for his deadeye precision target skills and for the use of his Peacekeeper revolver.He managed to make a name while a member of the Deadlock Gang, in which he dealt with weapon trafficking, until he and his associates...

Since his debut in 1987, Capcom’s Blue Bomber has become a true legend with dozens of video game instalments, cameos, and (most importantly) an army of loyal fans.The author of the dynamic diorama for 3D printing depicted the Blue Bomber accompanied...

In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of Darth Maul clothes’ seams. For you to achieve the cleanest 3D printed result, the character’s head, gloves, boots, cloth...

You take the red pill, you stay in wonderland, and I show you how deep the rabbit hole goes.”In the mystical sci-fi world of The Matrix, Morpheus appears as one of the key characters and our guide to the truth through perilous obstacles and swarms...

ABOUT THIS 3D FIGURINEArcane: League of Legends has taken the world by storm, bringing an innovative animation style and vibrant, life-like characters to the screens. Where steam-punk and fantasy genres meet, our hotheaded protagonist Vi shines best!...