davinci clock 3d models
17129 3d models found related to davinci clock.
thingiverse
This is a custom belt tensioner designed specifically for use with the Davinci 01 printer. Its purpose is to apply consistent pressure from a user-adjustable knob that pulls the belt tight and keeps it secure. By doing so, this tensioner effectively...
thingiverse
Video can be found here: https://youtu.be/0SO7Gl-gxPo Editable Fusion 360 source files can be found here:https://www.cgtrader.com/3d-print-models/games-toys/toys/3d-printable-davinci-catapult-gift-card Because many people liked my previous gift card...
thingiverse
... Files\Ultimaker Cura X.X <p>To report any issues, click <a href="https://github.com/Toylerrr/Cura-for-DavinciAiO/issues">HERE</a></p> <h3>Firmware Installation</h3> Use Repeter firmware for this to function correctly. Follow the guide at HERE
thingiverse
This is an external spool holder for the XYZ Davinci Jr 1.0 3D printer. It uses the little "rolly" things, screws, and nuts from the original spool holder. It can fit rolls up to 6 cm thick. In order to mount the spool holder to the side of the...
thingiverse
Post-Printing Mounting screws I designed this bracket to be screwed onto the DaVinci first, install the board, then screw it down. However, it holds the board securely without any screws. ...After verifying that normal screws can self-thread into the...
thingiverse
Print Settings: Printer: XYZprinting Davinci 1.0 Pro Rafts: No Supports: No Resolution: .3mm Infill: 25% How I Designed This Problem: Filaments were cutting into the spool holder and feed hole in the back of the printer, causing issues with filament...
thingiverse
I fitted an MK8 extruder directly to my DaVinci 1.0A without any modifications, drilling or cutting. I wanted to share this method because it's much easier than the other mods I've seen for the stock extruder. I used the original heater to save time...
thingiverse
This spool holder is designed specifically for the XYZ DaVinci 3D Printer, accommodating spools with an inside diameter of 32mm. The model targets big Octave ABS spools, which measure 160mm in diameter and 100mm wide. This premium spool holder...
thingiverse
Print Settings Printer: DaVinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to perform a significant amount of carving to get this to fit properly. ...I need to update the drawing, but with some effort it will fit...
thingiverse
This is my fourth iteration of an adapter designed to enable use of an E3D V6 on a DaVinci 1.0A printer. A considerable amount of effort was invested in making this work with minimal modifications. The stepper motor assembly is relocated upward by...
thingiverse
I bought a PrintinZ print bed for my XYZ DaVinci Pro. My binder clips were either too big or too small so I made my own. 2 clamps at 20mm wide go in the front. 1 clamp 10mm wide goes in the back. Print in ABS with 50% infill. There is a brim on the...
prusaprinters
Print instructionsCategory: 3D Printer Parts Print Settings Printer: Davinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to do a lot of carving to get this to fit. ...I need to do an updated drawing but it will fit with a...
thingiverse
Replacing the old fan is extremely easy as you can utilize the same fan and connectors, and the DaVinci repetier firmware lets you control the fan settings for each print individually. Update: I added version 2 that's elevated 2.5mm at the bottom so...
thingiverse
This modification replaces the stock Davinci extruder on the MK9 for optimal performance. It's crucial to note that it functions exclusively with linear bearings, which must be incorporated into the design for seamless functionality. To facilitate...
prusaprinters
It seems to work better than the stock but isn't up to par with what I expected. Print instructionsCategory: 3D Printer Parts Print Settings Printer: Davinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to do a lot of...
myminifactory
Video can be found here: https://youtu.be/7eT6KxMqU0A Because many people enjoyed my previous gift card, which was a fully 3D-printable wind-up car gift card (https://www.thingiverse.com/thing:3308711 and...
thingiverse
My E3D V6 hot end carriage for my Davinci Pro 1.0 I have an old Davinci Pro 1.0. I bought it when they first came out way back in 2015. I pre-ordered it and got a discount. It has been a good printer over the years and of course I have done some mods...
prusaprinters
You may need to trim the leads coming out the back of the switches to get them to sit flush on these mounts, but it did not adversely affect anything. The NEMA 17 motors have a longer post but shorter body, so I am including a spacer that gives it...
thingiverse
The issue is detailed here http://voltivo.com/forum/davinci-hwmods/41-squeaking-and-or-circles-arent-round-check-this-56k-warn/reply/7767 and the solution is to replace the pulley with this part and ball bearings and you may also have to replace the...
thingiverse
Since my Davinci 1.0's stock extruder idler became worn down and unusable, I've been searching for an alternative extruder but there aren't many options available.\nI attempted a printed extruder which uses a bearing as an idler that worked well, but...
thingiverse
This is the E3D v6/Lite6 mount for XYZ Printing daVinci Jr. It's supposed to fit in stock Jr, no RAMPS mod required or so (obviously if you've done one it will work as well). To get it up and running, you'll need an E3D v6/Lite6 heated bed itself and...
prusaprinters
DO THIS ON YOUR OWN RISK!!!I'm not responsible if you manage to fry your printer, any parts or even your house.Use common sense when wiring and mounting things.Never leave printer going unattended.If you haven't done anything like that in the past...