datsun 260z 2 2 3d models
865558 3d models found related to datsun 260z 2 2.
thingiverse
it also leaves the inner angled section of the Speedhut Stealth black bezel visible, which I believe is more visually appealing than my original design that came all the way to the gauge face Each pod has 4x .1" holes modeled between the two halves...
thingiverse
Bracket to hold a 33mm diameter flasher relay that doesn't have a mounting tab. ... Printed without support.
thingiverse
Pin for the center of the plastic rivets on interior.
thingiverse
This is a cap designed to seal the stock antenna hole, ensuring it remains watertight by using a gasket or sealant. ...It prints without any need for supporting structures.
thingiverse
These are the end caps for the chrome window trim. ...
cults3d
Post holes are threaded for M4, I cleaned them up a little bit with a tap. ...You can run M4 bolts from the inside of the hood if you prefer that to plastic pins.
cults3d
Pin for the center of the plastic rivets on interior.
cults3d
Bracket to hold a 33mm diameter flasher relay that doesn't have a mounting tab. ... Printed without support.
cults3d
This is a cap to block off the stock antenna hole. You'll want to use a gasket or sealant if you are worried about waterproofing. ... Printed without support.
thingiverse
Posts are drilled with M4 threads, and I tidied them up using a tap. ...If you'd rather, you can insert M4 bolts from the inside of the hood instead of relying on plastic pins.
thingiverse
Tool for installing the rear main seal in Z Cars
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=273099 Instructions Using the following settings: Letter depth = 2 Border distance = 5 Border radius = 10 Base depth = 2 Y name 4 = -15 Y name 3 = -5 Y name 2 = 5 Y name 1 = 15 Letter size = 7...
thingiverse
Customized version of http://www.thingiverse.com/thing:345972 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=345972 Instructions Using the following options: type = 9.6 flat = 0 length = 2 width = 2
thingiverse
Datsun 240z, 260z, 280z seat mechanism / recliner handle cover
thingiverse
... walls that are 2 units thick. It also features a top clearance of 0.2, a lid with thickness of 2 units and an edge thickness of 0.5 units, a bottom that is 2 units thick, and rounded corners with a radius of 5 units. ...The box's width is 40 units.
thingiverse
... created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=29211. ...For instructions, set gridY to 67, gridX to 40, thickness to 2.5, meshSpace to 2.5, meshSolid to 1, and add borders of 3 units in both the Y and X axes.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Using the following settings: Loop font: Gloria Hallelujah Loop y position: 2 Letter 4 height: 9 Loop character: O Letter 5 height: 4 Letter 5 space: 10 Letter 3 space: 10 Letter 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Instructions Using the following options: loop_x_position = 9 twist = 7 center = 43 rotation = 50 font_name = Chewy text = Ching letter_1_space = 13 letter_4_height = 6 loop_font =...
thingiverse
Created with Customizer! ... **Instructions** Use these options: Num Segments Set to: **4** Wire Diameter: **1 mm** Smoothness: **Set to 30 Steps** Ring Radius Multiplier: **Multiply by 4.2 Times the Outer Diameter**
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: pen_length = 130 font_scale = 2.1 font_spacing = 0.81 word = CHAJIHOO
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: picture_orientation = horizontal layer_height = 0.2 number_of_layers = 12 text_vertical_position = 0 text_reverse = no pane_size = small...