dark souls 3d prints

Best printed with PETG at 100% infill. The larger version (stl and 3mf included) are specifically sized for the newer style pumps that use the clip on nylon base. They will work with the screw on style metal base. Usage of the mold/die remains...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

...There is a preview .stl--nothing to print yet! Updated with v2 parts 09/21/2017: Added longer V2 parts that use two screws for better clamp support, similar to a woodworkers clamp. If you are shooting for light and cheap stick with the V1 clamps.

I printed in PETG, Black, Orange, White. Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held...

In a pinch (if your printer has issues printing these tiny bastards), you might be able to get away with some clipped up bits of the unused horns included with your servos. I designed the junction of two shoulder pieces to be held by two 3mm x 6mm...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI A kinetic sand piece that rotates via an electric motor with a pinion gear of 11mm, and rakes the...

Print Settings Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and "Twin Turbo" letters...

This is better than putting an oscilloscope probe in your helping hands. Print instructionsRoadrunner Probe Revision A Released 2020-10-04 Copyright (c) 2020 Josh Myer josh@joshisanerd.com Released under a Creative Commons CC-BY-SA license What is...

Print these two pieces out then hot glue them to your broom and refrigerator. My broom has its brush cut at an angle, so orient it so that it naturally falls over towards the back of the fridge. I designed this for a .85" diameter broom stock. Let...

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and strengthen...

Once I print some more of this I will keep tweaking it - and look to finish meshing a magazine. Nov 29, 2019 Part 2 - YEEUH. HUGE update! I've found a way around a lot of the hard stops of the limitations of space and dimensions, but still...

UNC 1/4 20 - http://ali.pub/4kpo3g I use high-speed epoxy to fix the screw and handle AB Glue Epoxy - http://ali.pub/4hvg7o The elastic that is yellow in the picture is a TPU filament - http://ali.pub/4kpplb I printed a knob from PLA filament -...

Always turn it off after use and keep an eye on the battery charge.One battery charge should yield 6-12h of usage (depending on resistors and IR LEDs)If you want to use your Wiimotes with the Dolphin emulator on PC, you still need to connect them via...

This is for the sketch and schematic. the list 1 Arduino Nano 1 HC-SR04 sensor 1 MP1584EN power supply 1 Songle SRD-05VDC-SL-C relay 1 BC548 transistor 1 1N4007 diode 1 LED 1 330 ohm resistor 1 2.2k ohm resistor 2 KF301-2P screw terminals 1 8-32 X 1...

This gives me enough string that when I loosen the ligature I can easily get the reed on the mouthpiece, and when I tighten the mouthpiece I get as much tension as I could possibly want. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts:...

# Warning **PLEASE PRINT OFF THE SHROUD AND MOCKUP 4010 BLOWER AND CONFIRM FITMENT BEFORE PURCHASING OR MODIFYING ANYTHING! PLEASE POST IN THE COMMENTS IF THIS SHROUD WORKS FOR YOU AND WHAT CARD YOU HAVE INSTALLED** The shroud is designed to sit...

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

Just put the LEDs and alarm speaker in a box with a labeled side (printed in white filament) and attach it to power supply fan connector... there is even a slot in my power supply cover to allow the wire to be slipped into (and out of) the power...

Plastic parts printed in PETG, layer 0.2mm, walls/top/bottom 1.2mm, infill 40%. With good part cooling supports are required only for the lower groove of the tool holders. Development log: 04/09/2023 Working sample 04/10/2029 "Head"...

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

I did just make them to show how the frame look like. Printer settings:Infill- 36% Grid patternPerimeters- 4Hight- 0,2I needed to use XY compensation +0,2 on my printerHAPPY PRINTING!  You need: 4 props where 2 is CCW and 2 is CW12pcs M3x8mm...

and post some makes if you use these it lets me know I'm not wasting my time uploading my designs and if you like what you see check out more of my lures at https://www.theneverendingprojectslist.com/ Print Settings Printer Brand: MakerGear Printer: ...