dark mechanicus models

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

Perfect for storing jewelry, electronic parts, cables, Lego models, tools, and other small items, the Pyramid Stacker offers a practical solution for keeping your belongings organized and within reach. By stacking the layers, you can store smaller...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The very bearing is a round 4mm rod with a thread just at one end, available as model landing gear axle. "009a_servo_gear" Juan's design provides very small holes for the screws, fitting the gear to the pan servo disc. Since drilling...

Some overhang areas in the inside don't bridge well, so you'll need to do some trimming / post-processing.Updated 5/2/2021:I added aluminum foil tape (HVAC duct tape, buy at any home/hardware store) for 3 reasons:serve as heat spreader so that the...

This 3D-model adds a calendar function which shows the day of the week and date mechanically to a common quartz movement.Simple mechanism with less load to the movementConvertible between desk and wall clockLess parts count (10 parts + optional...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the bottom. This could then feed the esc and also a water cooled motor plate. I also have a retro styled...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 34 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

I tuned them with an equalizer to make them sound good again, but someone more knowledgeable may remix this model or utilize the screw-on back feature to make them sound better. How to assemble Step 1: Unscrew the original driversTo do that, take off...

After the actual print of the model has started the control switch can be quickly flipped to the Auto position to enable the auto power off of the printer at the end of the print.  If at any stage you wish to disable the auto off function, simply...

I won't go into any more detail because it involves mains wiring and if you're legitimately comfortable with mains you should be able to easily wire it up any way you please. The cover has melted/pressed in brass M3 Threadletts for durability. The...

* The Ridgid adapter / switch part that you previously had to purchase separately is no longer needed, it is modeled in. You use more of the same brass strip used for the Ryobi part to create the Ridgid battery contacts. * The clips for the Ryobi...

The models are properly oriented for printing, and like most of my prints no supports are needed.Included STEP Files3D printing is all about making something new, unique, or customized. Therefore I always include the STEP files. You can use these to...

Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the bottom. This could then feed the esc and also a water cooled motor plate. I also have a retro styled...

The engraving starts at 1.8mm and the model continues at 2.2mm. Use contrasting colors for a clear reading. <b>note:</b> <i>* If you suffer from corner bulge / swell or an elephant’s foot after printing, carefully sand / deburr them. When...

Case: Case Full is a full model of the case. Case Right and Case Left are a split version made to fit on the Ender 3. If using the split case files, use pieces of 1.75mm filament to join the two halves. I test fit the components together with the...

Inspection: In order to assess this model, you will need to use a vernier/micrometer to check; Wall thickness (2mm ±.1) x 4 walls Internal Space (23mm±.1) x 2 walls Overall Height (25mm ±.15) x 4 corners Internal Height (23 mm ±.15) x 2 spots If you...

Don't forget to like this model and Share it with as many people as you can if it's helpful to you! Keep On Growing! <Center><B>03/08/2022 UPDATE!</B></Center> <U><Center>THERE AREN'T ANY RETAILERS AUTHORIZED TO SELL THIS DESIGN!</U></Center> ...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

Legal notes 3D printable file and model ©2022 Bethesda Softworks LLC, a ZeniMax Media company. All Rights Reserved. This is an STL ONLY for 3D printing and not a physical product. Requires a 3D printer and knowledge of 3D printing to use STL files...

CHECK THE MEASURES OF YOUR ROUTER MOUNT BEFORE YOU PRINT THIS !!! There are many CNC 3018 Pro out there, as this fits my model it may not fit yours, please measure the parts against you router before printing. I use my router mainly to make PCB, but...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Details and models may change as I continually improve it. Please see the pictures for individual printing instructions. If the spur gear for the table binds when rotating the table, loosen the stepper bolts, push the stepper inwards, and tighten....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

You may find it easier to thread some thin cotton through, first, and use it to pull the rubber band through. Attach a small accessory, such as a bell, to the lower split ring Consider attaching a carabiner clip to the top split ring for easier...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

I usually split such models on 2 or 3 parts that are easier for printing. Then these parts can be glued as a one piece (with acetone for ABS, or dichloroethane for PLA). So other version of parts I am uploading is prepared in this way. My black...