dan wesson airsoft revolver shells 3d models

This is a set of 3 shot shot shell that will fit into the airsoft ASG dan wesson 715. I have combined the 3 shot shell into a six shell clipped set. the original file, set of shotshell 357 works in my model of the 715 just fine. the second file...

I found that the 3.2mm shells performed similarly to high-power brass shells, while the 2.8mm shells achieved a reliable velocity range of approximately 360fps to 330fps when using a fresh CO2 cartridge. For users who wish to perform further tuning...

This device simplifies loading and reloading for airsoft Dan Wesson revolvers. It can accommodate six replica bullets. ...Effortlessly discharge rounds into the chamber by slotting in a bullet and rotating it out from the endpoint.

I'm just re-uploading it so people can continue to use it.From OP;"Makes it easier to organize and reload rounds for the AIRSOFT Dan Wesson revolver series.Holds 6 of the replica cartridges. ...Easy unloading into chamber by inserting the round and then...

Remix of "Gun stand - Dan Wesson or similar size revolver" https://www.thingiverse.com/thing:4310439 I've printed it as two parts. ...Works fine with my DW8" Made to work with with "dan wesson BB clip"

Remix of "Gun stand - Dan Wesson or similar size revolver" https://www.thingiverse.com/thing:4310439 I've printed it as two parts. ... Works fine with my DW8" Made to work with with "dan wesson BB clip" https://www.thingiverse.com/thing:289983 Feel free...

... users and features six holes for ammunition. To prepare your gun for use with this Holster, you'll need to re-drill the holes for bullets using a 9.8mm drill bit. The design is modeled after an Airsoft replica, which uses proprietary ammunition.

If this isn't cool, I don't know what is: A custom shell for your Dan Wesson Airsoft Revolver that holds up to 6 BBs instead of one, basically turning it into a mini shotgun. I designed it to be printed very tightly in my printer, meaning the first...

To keep a Dan Wesson 6mm BB revolver loading smoothly, try adding an elastic band to the grooved section of the speedloader. This elasticized tool effectively holds each cartridge in place until they're precisely seated. ...Just gently stretch off the...

This shell was crafted specifically for use with Dan Wesson Revolvers, chambered in 6mm BB cartridges. Its standout feature lies in its ability to fire multiple projectiles simultaneously, much like a shotgun blast, discharging up to five BBs at...

This is a Shell for the Dan Wesson Revolver designed for 6mm BBs. The Feature that makes it special is the "Shotgun-like" capability of shooting up to 5 BBs at once. You may have to scale it to fit you printer accuracy. ...Feedback is strongly...

Compact accessory for DAN WESSON (airsoft replica). ... Dimensions: Length - 20cm Width - 5cm Height 5cm Printing time: 3 hours

This holster is based on Revolver Dan Wesson Magnum 6" 357 for 6mm airsoft, is for right hand

Single shot version of https://www.thingiverse.com/thing:4590104 Once again tested only in 715 version, shell SHOULD fit other version, clip fits only 715 version. In my 715 2,5" 2.6mm version gives same power as stock full power brass shells.

Single shot version of https://www.thingiverse.com/thing:4590104 Once again tested only in 715 version, shell SHOULD fit other version, clip fits only 715 version. In my 715 2,5" 2.6mm version gives same power as stock full power brass shells.

This custom-made holster is specifically designed to fit the Dan Wesson Magnum 6-inch .357 revolver, but tailored to hold a 6mm airsoft version. ...It's perfect for right-handed users.

A full RIS system for the Dan Wesson 715 6" version. This system mounts onto the revolver using a screw at the top rear that replaces the sight screw and is assisted by the front sight. You can use longer screws for the rail on the underside for...

A little present for my fellow ASG Dan Wesson revolver lovers. a little sanding may be required on the rail depending on your printer. ...keep being awesome

AST revolver Shotgun Shell singles allow you to convert your wingun, ASG, G&G, Gameface, Skeleton Sidearms etc etc airsoft revolver into a shotgun. These guys come in 1bb through 6bb varieties, with each shell featuring markings that denote the...

This is my concept for a compensator with a top rail designed specifically for the Airsoft Dan Wesson 715 4". As this is my initial attempt, there may be room for improvement, but it functions effectively as intended. ...I plan to refine the design if...

The Dan Wesson revolver has a simple gun stand that fits its design perfectly. ...The ammo stand, however, is limited to use with 4.5mm CO2 ASG ammunition and the SAS star, making it not universally compatible.

A free accessory that fits the Dan Wesson airsoft pistol perfectly, this shell unleashes a powerful blast at an impressive 285 FPS on a .20 gram weight or a whopping 0.32 Joules on a .25 gram weight when the rear of the shell is carefully drilled out...

Simple gun stand for Dan Wesson or similar revolver. Ammo stand is only ok for 4.5mm CO2 ASG ammo of this gun, and the SAS star. Print instructionsNo raft, no supports, designed to be printed in 0.20mm and with 10-15% infill.

A 9mm caliber cartridge designed to accommodate 4.5mm steel balls for use in Dan Wesson revolvers or the Ignite Black Ops airsoft pistol.

A standard Dan Wesson shell holder works perfectly with all types of shells, fitting tightly to prevent them from falling out. There's no requirement for a rim, and printing at 15% infill density produces excellent results. ...Additionally, printing at...

Bullet holder for the DAN WESSON airsoft 6 mm bb revolver

Dan Wesson 6mm airsoft bullets are printed with PLA flex, a flexible filament, using a 0.4mm nozzle. To witness the accuracy of these bullets in action, watch this shooting video at https://youtu.be/ihGvua7iWos. Another demonstration of their...

This is my version of https://www.thingiverse.com/thing:2320243 Original worked well with ASG Dan Wesson. However I wanted to replicate it to understand how and why that tactile feedback works. While at it, I also decided to make it a bit more...

While at it, I also made some ergonomic changes to make it easier to use in conjunction with Dan Wesson. Warning: I don't have access to actual guns or ammunition, so I'm unsure if it will work with them. The dimensions were taken from sthone's...

Shell created for the latest version of airsoft ASG Dan Wesson 715 revolvers. This shell is designed to shoot three rounds and can be added into a moonclip. The base is a bit thinner than the brass ones so it won't wear the rubber seat on the 715. ...