daily contact lens dispenser 3d models

168205 3d models found related to daily contact lens dispenser.
Minimalistic Daily Contact Lens Dispenser (wall mountable)
Minimalistic Daily Contact Lens Dispenser (wall mountable)
thingiverse

As it prints, leave it undisturbed if its height exceeds your printer's limit, approximately 11 inches. If necessary, trim the top portion with your slicer. ...Apply adhesive to the recessed areas at the rear for secure attachment to a wall.

Daily Wear Contact Lens Holder/Dispenser
Daily Wear Contact Lens Holder/Dispenser
thingiverse

My daily contact come in boxes of 180 contacts. The contacts are packaged in interlocking strips of 5 contact lenses and stacked six strips deep so each stack is 30 lenses. This case is designed to hold a single stack of 30 lenses for both left and...

Daily contact lens box
Daily contact lens box
prusaprinters

A simple box for holding daily contact lens packages in a medicine cabinet.72mm wide, 77mm tall, 124mm deep. ... Can hold lens packages up to 33mm wide.

Daily Contact Lens Holder
Daily Contact Lens Holder
thingiverse

Simple holder for 5 (five) pairs of daily contact lenses (acuvue). The dispenser-style holders were too fiddly, so I simplified it to a slot system. Five slots, since a strip comes in five. ... The holder is just deep enough to put your glasses on top.

Daily Contact Dispenser V1
Daily Contact Dispenser V1
thingiverse

By using the lever arm, you can load the pairs of daily contacts from the top every three weeks and pull them out the bottom each morning. To secure it in place, I attached a VELCRO COMMAND STRIP PAIR up top, but two pairs would be even better for...

Daily contact lens holder
Daily contact lens holder
prusaprinters

The blue reference dimensions in this recess sketch are also referenced by other sketches, so edit the red dimensions in this drawing to change the geometry to fit your own daily contact lens packages. PrintingI've printed this in both PLA and...

daily contact lens organizer
daily contact lens organizer
prusaprinters

Simple bathroom organizer for daily contact lenses. Separate right and left lenses with this container.</p><p>I order them by 90 pcs (180 taking two eyes into account) every quarter and I needed a way to keep them organized as I was struggling every...

daily contact lens organizer
daily contact lens organizer
prusaprinters

Simple bathroom organizer for daily contact lenses. Separate right and left lenses with this container.I order them by 90 pcs (180 taking two eyes into account) every quarter and I needed a way to keep them organized as I was struggling every morning...

Contact Lens Dispenser
Contact Lens Dispenser
thingiverse

File under 'things I never knew I needed'. ... A simple contact lens holder/dispenser to help reduce bathroom clutter. ... Designed for 30mm x 44mm contact lens packs.

Contact Lens Dispenser
Contact Lens Dispenser
thingiverse

This is a dispenser for contact lenses/eye lenses

Contact Lens Dispenser
Contact Lens Dispenser
thingiverse

This Contact Lens Dispenser is a gravity fed unit that will hold a weeks (7 days) worth of contacts lenses for each eye. I designed this model around my specific brand of contact lens, so fitment might not be universal but i tried to add some buffer...

Contact lens dispenser
Contact lens dispenser
thingiverse

This is a simple dispenser for contact lenses, dimensions are specific for the Acuvue Moist 1 day, but probably will accomodate most pouches. ...Capacity is for 15 days, or 15 units on each side for dailies, if used for monthlies, will cover the whole...

Contact Lens Dispenser
Contact Lens Dispenser
thingiverse

Currently constructed to accommodate BioTrue 1-day contact lens packs, I've included the Fusion360 file allowing customization of the dispenser's shape by editing the profiles in the first sketch, with changes cascading accordingly. Print vertically...

Contact Lens Dispenser
Contact Lens Dispenser
thingiverse

Contacts dispenser, designed specifically for the CooperVison MyDay contacts that I wear but it should fit any contacts with maybe a little bit of scaling. Dimensions below: One side Inner Dimensions: 30x40 mm Your contact lens case may be longer...

Contact lens dispenser
Contact lens dispenser
thingiverse

A simple dispenser for contact lenses. This was sized to hold 10 Acuvue contact lenses, which are 30x45x9mm in size. ...STEP file and Alibre Atom source files are also provided for modification.

Smart Contact Lens Dispenser
Smart Contact Lens Dispenser
thingiverse

... and built. https://youtu.be/Lj-hJU5XPVM Consider subscribing to my YouTube channel for more incredible projects like this one. For more information, check out my Instructable as well: https://www.instructables.com/id/Smart-Contact-Dispenser/

Contact lens dispenser
Contact lens dispenser
cults3d

This is an eye lens dispenser. It allows the lenses to be inserted in groups of 5 as packaged in the box. The vertical opening makes the correction index permanently visible on both sides. 2 cut-outs on the underside allow the distributor to be...

Contact Lens Dispenser
Contact Lens Dispenser
thingiverse

When putting contacts in, keep them facing up but alternate the direction by 180deg so that they don't sag. Tested with Acuvue Oasys contacts, but probably work with others too. ... I like to leave the drawer out, and then when I need contacts I push...

Contact Lens Case Dispenser / Holder
Contact Lens Case Dispenser / Holder
thingiverse

Contact lens case dispenser/holder. The case for the current lenses in use is stored at the bottom. The second to last is the "next" case dispenser. Reload cases at the top. Walls are 2mm thick by default and they're pretty stiff. ...Printed with...

Acuvue Contact Lens Dispenser & Holder
Acuvue Contact Lens Dispenser & Holder
prusaprinters

Might work for other contact lens brands but I measured and design this for Acuvues.The best way to put the contact lenses in is face up (the rounded part on bottom/written part on top) and facing backwards (the text should be upside down to you when...

Acuvue Contact Lens Dispenser & Holder
Acuvue Contact Lens Dispenser & Holder
thingiverse

The best way to put the contact lenses in is face up (the rounded part on bottom/written part on top) and facing backwards (the text should be upside down to you when you are standing in front of the dispenser). I printed this in PETG and no...

Contact Lens Case Dispenser / Holder
Contact Lens Case Dispenser / Holder
prusaprinters

Better pictures: https://www.thingiverse.com/thing:4896952Contact lens case dispenser/holder. The case for the current lenses in use is stored at the bottom. The second to last is the "next" case dispenser. Reload cases at the top.Walls are 2mm thick...

Daily Contact Dispenser
Daily Contact Dispenser
thingiverse

I'm thrilled to be sharing my first post with you all, and I must say that I'm absolutely loving the Shapr3d app on my brand-new iPad. It's become an essential tool for me, allowing me to stay connected with friends and family throughout the day. ...The...

Bausch and Lomb daily disposable - Contact Pair Dispenser
Bausch and Lomb daily disposable - Contact Pair Dispenser
myminifactory

A coworker approached me at the office and requested that I create a contact lens dispenser for them. ...I naturally replied, "Why not?" This project would be specifically designed for B&L's daily disposable lenses.

Bausch and Lomb daily disposable - Contact Pair Dispenser
Bausch and Lomb daily disposable - Contact Pair Dispenser
pinshape

A colleague approached me at the office and inquired if I could create a device to dispense contacts. ...Without hesitation, I responded with an enthusiastic, "Absolutely!" This dispenser will be tailored specifically for B&L's Daily Disposables.

Bausch and Lomb daily disposable - Contact Pair Dispenser
Bausch and Lomb daily disposable - Contact Pair Dispenser
thingiverse

A colleague at work inquired if I could create a dispenser for their contact lenses, and naturally I responded with a resounding "why not." This is specifically designed for B&L's daily disposable contacts.

Contact Lens Dispenser for Medicine Cabinet Shelf
Contact Lens Dispenser for Medicine Cabinet Shelf
thingiverse

Contact Lens Organizer for Bio True OneDay Lenses. Made to hold Bausch and Lomb's Bio True OneDay contact lenses, it will probably fit other sizes too. The organizer is 4 inches tall and holds 10 each of right and left lenses. It fits perfectly on a...

Daily Contact Lens Travel Holder With Lid (5 Pairs)
Daily Contact Lens Travel Holder With Lid (5 Pairs)
thingiverse

Contact lens travel case for carrying 5 pairs of contact lenses. ... This is designed to fit 1 pair (2 packs) in each slot the pack sizes for the lens are 45mm x 27mm x 7.5mm each.

Contact Lens dispenser
Contact Lens dispenser
thingiverse

I needed a way to streamline my communication channels, so I created this system. ...To build it, I utilized three industrial-grade power adapters and securely fastened them to the wall adjacent to my shower area.

Contact Lens
Contact Lens
grabcad

Contact Lens