cz scorpion models

Make sure to follow me to get a notification when it's uploaded!*** ###READ BEFORE PRINTING!### * First of all, this is a non-commercial print, this means you are not allowed to sell files or prints of this model. Not that I neccearily would have...

To aide in designing this part, I also ordered a complete Neo hotend assembly from Amazon so I could 3d model all of the parts. Unfortunately, the back plate is not available to buy, but I was able to download an stl file from another Thingverse...

Make it Free the figurine from the Lunochod modell. See the picture. Drill / cut through four tabs (red circles). Two starts are hidden (see the residues after cutting - the blue circles). . The Sandmann figurine has a metal tab with threaded...

If you need a lot more room (more than a few mm) you may need to update the model to scale it appropriately. (~$1 of filament)</li> </ol> <ol> <li>Light string or rope. Cut it about 5ft 6 inches, or just enough to make a loop on the elbows, running...

The files are prefixed with Updated_ or New_.Here are a couple videos of it running  Please refer to the Original model for assembly and any other sources.I have uploaded the file as a Fusion 360 archive folder so you will need Fusion 360, Fusion 360...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

Using a allen key also has a couple of smaller advantages, those being reducing the number of pieces in the model, while also providing the added benefit of acting as a keychain mount.The gadget is made up of a few common parts apart from the printed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

I based the design of these pieces off of the Ender 5+ model available on GrabCAD (https://grabcad.com/library/creality-ender-5-plus-1). There will eventually be a detailed pdf showing a build guide, confirmed material list, building and flashing...

A big thanks also to Eric Clinedinst who helped me to find the first issue. This is the BOM list for the internal part: 1x 5x10x4 (MR105z) Bearing for indirect filament sensor 1x round neodymium 8x3...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

To use a different font than the standard Roboto (English) for either (or both) of the lines of text you just need to install the font onto your machine and configure it in the model parameters (in Customizer *locally* or in your .json file, more on...

... other people might actually make! Haha. This was made with TinkerCAD. This is about as advanced as I get when it comes to CAD or 3D modeling at all. I'm very much an amateur with this stuff. ...That said I'm really happy with how it came out.

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height. Here's a video of the toy with some details. The video has a lot of assembly photos at the...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

**Update 2022/04/08:** Fixed a bug in main body model. It was slightly to long on left bottom side to fit nicely over the antminer case. This project aims to convert a Bitcoin miner into a handy space heater. **We achieve this by:** *...

I like you.text10 = ---textsizes = [13,13,13,13,8,8,8,10,6,10]Boat labeltext1 = Coast Guard Capacity Informationtext2 = ---text3 = Maximum persons|3text4 = Maximum gross load|100kgtext5 = Persons, motor &amp; equip.|50 poundstext6 = Maximum...

But don't hesitate to choose the one you prefer. The Raspberry Pi racks I designed are compatible with the Raspberry Pi 2B, 3B and 3B+ models. They should also be compatible with the 4B versions of Raspberry Pi, but I haven't been able to test them...

&nbsp;READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...

Enable the Rotate_For_Printing option to rotate the part in this orientation. Supports: Depending on the options selected, it may be necessary to use supports. Rafts: Doesn't Matter License The "Sidewinder X1 FFC Riser" models (.stl) are licensed...

I do not own a BL Touch so this design was based on 3D models so definitely WIP. I have increased the thickness of the Duct mount to the base unit to make it even more robust on the LH duct. You may now need to use M3 x 10 mm to fix to the base unit....

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...