cyberdyne systems model 101

Here is a view of the 3D model for illustration:In red the silicone is indicated, in green you can see the molded-in base made of PLA. The many holes in the 3D structure allow the silicone to adhere sufficiently well to the PLA part after curing. An...

On the X-Max you can have it installed all the time but I'm unsure of the other supported printer models.Print SettingsPrint the carriage in high temp resistant filament. I recommend using Polycarbonate (PC), a PC blend such as PC-FR (flame retardant...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

[Medium Sized Model - 25mm Base] (Note: Hendrak is significantly taller than most other humanoids) [Presupported with LYS files in 32mm & 75mm Scale]   In the farmlands of Avignon in Terra lived a young Henrique. His days were filled with toil and...

We don't use the shell.PrintingPrint all models in their original orientations.The faceplate should face down and needs no support. You might want to add a little bit of negative Z offset to this one for a squished first layer on a rough bed for a...

I originally started all of this in SolidWorks but as I went along I found I needed to revise my bars and I didn't use variables in my model so I had to make tweaks to the sketches. And I am inherently lazy. So to make a lot of different length...

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The...

If you are looking for perfection (and quiet printing) put the effort in to hand-fit the integrated bushing version and be amazed at the results.Post-Printing// model: Prusa i3 MK2/3/S/+ Y Chassis Bearing Straps with Integrated Bushings//.// author:...

A STEP file with all the final models is posted here, to make remixing easy. I only ask that if you make a change you like, please share your remix so everyone can benefit. I used Hatchbox Wood PLA for the sides and regular PETG for the other...

:) There are two variations of the model; one has an additional thin cutting edge that is 1 mm in height and about 0.5 mm in width, so if you have a 0.4 mm nozzle, it will be a single path wide. That's the one shown in the photo. It's probably the...

I also saw another model: https://www.aliexpress.com/item/4000497767128.html. I bought a pair of these with 9006 shape, for a Toyota which has projector type headlights. The light pattern seems ok and my eyes find them as bright as these 22000LM...

Had to drill this out a little to get them to fit.M3x8 hex socket head cap screw• 2 for the Tourbillon-balancewheel to add weightSome sources I’ve used10pcs 2x5x2.5mm MR52-ZZ Precision Ball Bearings Chrome Steel, Metal...

In some cases (like SUNLU), the LockSpool needs no channels because the manufacturer's own reusable spool is designed to be loose.This design produces spools compatible with these filament coils, and any others for which dimensions can be...

---- **Running the Customizer** Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own...

I first modeled the mold in F360 and printed a few iterations. Once those fit together I designed the MoldMold around it and printed a few more iterations. Printed at .2 mm layer height with a brim to prevent some curling up at the edges - this part...

And you can create two STL files for dual extrusion. Just downlod the SCAD file from the original nameplate:Then install OpenSCAD on your own computer and follow the customizing instructions on this page.Big thanks go out to RLazure for the...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Changelog: Version 6.115.Feb.22Version 6.1 has been released as experimental files. They should...

Customized QR and tag design for Thingiverse model #46884 using Customizer! ... Tag thickness: 3mm Corner radius: 10mm Round corners: Enabled Subtractive layers: 2 Tag width: 80mm Object type: Flat QR scale: 1.6x QR bottom left position: Origin...

Picture 5 is the most current model. Added small connection points to the outer case and isolators. This divides the light guides into 3 zones instead of a continuous line. This was done to make these parts less floppy, and easier to glue.</li>...

Alexander is depicted here with large eyes with modeled lids, slightly parted lips, and the characteristic creased forehead. His thick leonine hair is swept up at the forehead in with locks breaking to the left and right. Deep drill work is used...

Remix pro 7" touch panel / Remix for 7" touchscreen https://www.thingiverse.com/thing:4646683 by David Shearer 9/2020 - EN New: STP/STEP file include I'm currently working on a new model, this design has a bit of a problem. After screwing together,...

... springs, bottoms, top layers and tops. but the latest models are off course the best.Please share your towers so I can see how colorful and tall you can make them.And don't forget to check out my Instagram: fredslund3dGood Luck &amp; Happy Printing!

15.09.23 - Further updated design - Leaner models and thanks to a test printer from the handy discord community, I have included two versions - a no frills neat and straight one as well as a nice curvy one. Please do continue to test print and...

UPDATE 12/21/2021: Now includes an All Files.zip file UPDATE 7/16/2021: A spring-loaded Hammer has been added. The Hammer retracts when the Trigger/Slide moves backward and returns as the Trigger/Slide moves forward. If you have previously printed...

I planned to use sensorless homing and didn't need it, so I didn't add it. MiscIf you are wondering where the beautiful Hemera model in the pictures came from, here is a linkPrint SettingsPrinter Brand:AnycubicPrinter:Large Size...

And you can create two STL files for dual extrusion.&nbsp;Just downlod the SCAD file from the original nameplate:Then install OpenSCAD on your own computer and follow the customizing instructions on this page.Big thanks go out to RLazure for the...

Example source: https://www.etsy.com/listing/569619485/3-wooden-baseball-bats-free-shipping• If the bat has a cupped end, flatten it with a saw then sand it.Paint and Supplies:• Red, neon-ish blue, vivid yellow, neon-ish pink, black, white, brown...

It was the perfect model to start with as it was multi-part, required many "sketches" to build and extrude, and it required many different skills to complete. I reference sides in this posting, please refer to the "orientation" image (2nd image) to...

This might seem obvious, but it may not be; the led's needed to be mounted securely, and the front was too thin at that point. added: (same as for the LEDs) more plastic for the display to mount in. changed: re-created the screw holes for the...

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume. &nbsp;She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together. The...