custom ebike 3d models

I created a custom mount for my NCM Moscow e-bike for the unit. It will work with many of the 7" and 9" Android Auto units on Amazon. They all use approx the same base. It is important to print everything in an orientation that helps support...

This is for the bike light on a radrunner plus. it requires 4x m4x20 with nuts and 1x m5x8 with a m5 washer and nuts. the assembly on the top handle bar is simple but does require patience. ...make sure you tight the light before anything else and...

I've modified the original text for better readability. The controller box was designed specifically for older Kona bikes, but it's versatile enough to be mounted on any bike frame with a rear angle closely matching 88 degrees, as clearly shown in...

Переходник позволяющий установить датчик тормозной ручки от электромоторкомплекта на комборучки Shimano ST-EF50. на другую ручку распечатать зеркально. поддержки= обязательно, пластик - любой. потребуется винт м3х5+/-1мм, переходник накидывается на...

I like the Bosch Charger Wall Mount by Berndte. ...Made my own Plug Holder just for fun :)

This is my DIY electric bike inspired by Tom Stanton video. Parts list: Motor: ALIEN POWER 6364 Motor 190KV £40 ESC: VESC V4.12 £63 Controller: Teensy 3.2 + ILI9341 LCD £30 Pedal Assist: PAS Sensor 12 Magnets £6 Bearings: 2x F688Z £1 Belt:...

Create a prototype package based on available illustrations of the BBS02 online.

Modified the wall charger mount to accommodate a 4A charger by making a simple adjustment - stretching the existing design to match the larger charger's requirements.

Dust cover for the Rockrider ST-500 MTB to keep the contact for the battery clean during transportation when the battery is disconnected.

This is a remix of https://www.thingiverse.com/thing:4824838 as it was too small for the new 36/4 charger. I did not want to just enlarge it as it would have malformed the round parts. ... So I split the object and made it wider but keeping...

My son's Swytch kit magnet ring lost some of it's teeth and became loose. ... This is a copy of the inner ring (which can be separated from the magnet ring), print in PETG for best results

The mounting bracket for the Gazelle battery and the signal box fit snugly into a sturdy chrome frame designed specifically for the Terragiant.

This adapter cable can be used to charge Bosch e-bike batteries from a suitable voltage source with XT-60 connectors. ...This work was inspired by: https://www.thingiverse.com/thing:4693390

Wird wie ein Trinkflaschenhalter montiert und trägt den 2. ...Akku für das Suhsi Bike Maki 1 von meinem Sohnemann

3D printed power switch mount for an ebikeHeld together using M3 bolts and nylon lock nuts.

This is a protective cover for Bosch Compact Chargers found on many Active Line and Performance CX motorized electric bicycles. ...Two versions are available: a hollow "cover" that completely encloses the entire connector, and a filled "cap" that...

Raincap for Bosch Nyon 2 printed without supports with a layer height of 0.1mm Please give a Like!

Those plugs for the speed sensor get lost often. So I used one original plug too create my spare part. ... Fits fine and the screw holding the sensor is covered again

Additional support for my Hailong battery from Yose Power. ... Fits frame with 40mm tube.

I like the Bosch Charger Wall Mount by Berndte. ...Made my own Plug Holder just for fun :)

I search my Yamaha bike LCD every spring. This time I bought Apple AirTag and made this bracket to mount it to the LCD. ...Printed in PLA.

Cable Guide for Reention Battery Case. just put a Zip-Tie inside the Controller base to get strain relief on the Cable. It is a 7MM Hole for Bafang BBS02 Power Cable thickness. ... 0.12 layer hight Hole entrance Facing up for print.

Remixed to fit the throttle on a Lectric XP - as I recall the linked thing was too large. It's just a friction fit on the rubber twist throttle. Print it off, remove right hand grip, and slide the thumb-throttle onto the twist grip. Find a good...

Mount a Bosch e-bike charger to the wall securely.

Humans are a complex and multifaceted species, characterized by their unique blend of intelligence, creativity, and emotional depth. Their capacity for language, culture, and self-awareness sets them apart from other living beings on Earth. ...Humans...

Folding e-bike, the sleek Ibiza model by Littium-Kaos, has undergone a meticulous transformation through advanced 3D scanning and optimization techniques that refine its mesh and textures to perfection. ...Disassembled into distinct components, each...

The original design was great but I needed something bigger to fit 52 batteries in 13s4p 48V configuration. XT60 connector (controller) DC 2,1/5,5 connector (charger) Relatively tight fit like in the original. You can try to print all parts in...

mud guard for E22, recommend to attach with double sided adhesive tape

<p>Holder was printed in PETG (40% Infill), a rubber mat is glued to protect the bikes surface.<br>Fastened with three M5 cylinderhead screws.</p>

My wife wanted a way to have easy access to her cell phone while she was riding (she stops a lot to take photos ). Her Radcity Step-thru 3 has four bolt hole on the front fork. They can be used for a front rack. I designed a small box to hold her...