cubicle picture hook 3d models

This is a low profile hook specifically designed to allow framed pictures to sit well on an Ikea Skadis pegboard system.Sometimes the frame does not want to sit flat against the board or has a desktop mount which causes it to twist.   In that case...

This is a low profile hook specifically designed to allow framed pictures to sit well on an Ikea Skadis pegboard system.Sometimes the frame does not want to sit flat against the board or has a desktop mount which causes it to twist.   In that...

In contrast, the hook that came with the command tape broke under the weight of this same picture. I Printed it in PLA with a Taz 5 without raft direct to PEI print bed so the back is smooth (it must be smooth or command tape won't hold). I also...

2 picture hooks (the ones with a groove – see the images if needed). Check out the pictures for tips on assembly. If your hook isn't fancy and slips into a slot, simply pass the wire through each side – that's what I did. Additionally, the frame's...

I designed a simple two-sided hook for my 6mm glass wall shower cubicle. It seems pretty sturdy and should easily hold a wet towel. ... Please, select size according to the thickness of your glass wall/door: 6mm (as pictured) 8mm (not tested) 10mm 12mm...

I crafted this uncomplicated hook specifically for hanging panels or paintings on the wall. One part is securely fastened to the wall using two straightforward nails that are approximately 2 mm in diameter, while another part is attached directly to...

original didnt fit so i adjust it. print in whatever, i use PLAprint with any profile, i used 0.3 hang pictures, cloths, towels, decoration or anything you like.

Once this was done, I inserted the picture into the holder and pressed the others against the wall by pushing the picture towards the wall. After that, I removed all holders by shoving the pins out of the slides. Finally, I fastened the slider with...

Also posted on Thingiverse (6000+ downloads): https://www.thingiverse.com/thing:4868025---I designed a simple two-sided hook for my glass wall shower cubicle. It is sturdy and easily holds wet towels. ...I have even dried a packraft and tent hanging...

Customized version of https://www.thingiverse.com/thing:2848589 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2848589

Customized version of https://www.thingiverse.com/thing:2848589 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2848589

Customized version of https://www.thingiverse.com/thing:2848589 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2848589

Customized version of https://www.thingiverse.com/thing:3960392 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3960392

I fabricated it with a 0.3 millimeter layer thickness, 15 percent infill density, and four wall dimensions. ...It turned out perfectly fine.

Customized version of https://www.thingiverse.com/thing:2848589 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2848589

Cubicle-mounted coat hooks that clip securely onto the top edge of an office partition.

Engineering Cubicle

<p>... ...prostě háček na obraz.</p> <h3>Print instructions</h3><p>It can be printed from a PET-G.</p>

I have a laser cut kitchen decoration, I found the original model by Madpilot was almost what I needed. ...I fired up Blender and modified everything to what I needed.

alles Standard

<p>This is a small holder I designed to hold wall art where I was not able to conceal. It's made in two parts. 1_fixes to wall with nom. 3mm screw and has a small grove at top (twist to suit which end of world you are at!). Finished with twist on...