cubicle corner shelf 3d models

I adapted my cubicle wall hook to form a pair of brackets, screwed them to the bottom of a piece of 1x10 cut at 45 degree angles, and thus produced a corner shelf that sits securely atop the corner of my cubicle. No need for affixatives; the right...

It features two arms that latch onto the cubicle wall (the wall width is approximately 53mm) and secure to the bottom of the shelf. The arm height can be adjusted using the pre-drilled holes and the provided screw. I crafted two distinct shelves,...

4 different organizers that can be hung in a cubicle

Yet another office cubicle.

Fortunately, this shelving unit was designed to be perfectly positioned atop the corner of my cubicle, allowing me to maximize storage without encroaching on adjacent workstations. ...Specifically crafted for the MP Maker Select Mini V2 3D printer, it...

This modular 3D print storage surface features a customizable cubicle shelf that can be easily replicated and expanded as needed. The concept revolves around printing out multiple units, which can then be connected using a versatile base made from...

Humans use the Cubicle Expander to boost workspace capacity. ...Simple to produce and install into existing workstations.

I decided to craft a unique showcase for my three-dimensional creations right on the wall of my office cubicle. ... Updated, Modular Version: https://www.thingiverse.com/thing:2439255

To Maintain Office Cubicle Stability, Use a Support of Exactly 41.6 Millimeters.

Needed a coat hanger for my work cubicle and the mounting holes were there and just begging for a hook.Printed in PLA, 3 perimeters, 20% cubic infill. ... Has held up so far.

... cubicle. ...You need to print 2 left and 2 right hooks, attach to the end of a 1 inch shelf and hook over the sides of your cubicle. ... I have also considered attaching a second shorter shelf below the hooked shelf, but I'm concerned about weight.

A corner piece for a flapping cubible wall. Category: Office

In Addition To Printing The Brackets, You'll Need 2 1/2" Steel Corner Braces, A Piece Of Light And Sturdy Wood For The Shelf, And Bolts/Nuts To Hold Everything Together. For My Shelf, I Used A 1/4" X 5 1/2" X 24" Piece Of Pine/Spruce. The Brackets...

You'll need to print two left and two right hooks, then attach them to the end of a 1-inch shelf and hook it over the sides of your cubicle. ...Additionally, I've thought about installing a secondary, shorter shelf below the hooked shelf, but I'm...

In addition to printing the brackets, you'll need to pick up a pair of 2 1/2" steel corner braces (the L brackets shown in the picture), a piece of light and sturdy wood for the shelf, and some bolts/nuts to hold it all together. For my shelf, I...

... that when you change the grip size, you'll need to reposition the hook part to ensure a proper fit. You can obtain the STL file for this design at libre3d.com, where it is categorized under Frames and listed as Cubicle-Wall-Hanging-Shelf-Modified.

This is a cubicle shelf bracket I designed to attach over the top of a cubicle wall and support a shelf that spans its width. You will need to print four parts - two left and two right - before adding a 3/4-inch thick piece of wood or shelf material....

I discovered a simple solution by attaching this shelf to a wall, cubicle, or bulletin board using a pushpin or thumbtack. ...Although it's not designed to hold an incredible amount of weight, it is sufficiently sturdy for small printed models or...

This cubicle shelf makes use of the "steelcase" hook pattern to interlock within its seam, resulting in an extremely stable design. To achieve optimal stability, it would be ideal to have a hook in the middle section; however, this is not feasible...

First things first, I carefully removed the screw holes from the back of the design and added sturdy hooks that would securely fasten to my cubicle's framework (I'm not entirely sure if all cubicles accommodate standard hooks, but I'm crossing my...

You ever glance at the cubicle wall and ponder if you can install a shelf to those uprights between the panels? Check the holes - if they're 1 inch apart, this should fit. Measure from the top of one hole to the top of the next; if that's 1 inch,...

I wanted a little shelf for my bulletin board, and wasn't vibing with anything I could find on here. So I whipped up this little thing. It's not meant to hold much, just to hold small things and look good while doing so! There are two versions -...

Decided to design a shelf for my cubicle office wall. Just placed a nice looking wood plank over the top and was all done. They are offset to allow for fitting in the corners of spaces so make sure you pick the correct one when printing. Used a...

This nifty little clip is perfect for attaching a headset to a standard, steel cubicle shelf with a short overhang at the bottom. ...I also have another one that clips onto the top of a cubicle wall, which you can find here [WallTop...

<p>I wanted a fun way to display my minis at work, just for fun. ...So I made pin holes to put up a small shelf on my cubicle wall.&nbsp;For FDM it is best to print it upright to make sure the holes are strong enough.&nbsp;Have fun.&nbsp;

Corner shelf

Corner shelf

I designed this shelf to sit atop an 8" wide cubicle wall, 1" thick and sturdy. It's a convenient accessory that pairs well with the two hooks I created for these walls, making them an ideal combination. Print the shelf vertically to significantly...

The remixed coat hook was a hit so now I have a remix of the shelf. Remixing was done in TinkerCAD. Printed on an Ender 3 v2 with standard supports and this came out great. Removing supports from between the brackets on this one was very...

The remixed coat hook was a hit so now I have a remix of the shelf. Remixing was done in TinkerCAD. Printed on an Ender 3 v2 with standard supports and this came out great. Removing supports from between the brackets on this one was very...