cube world model

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

Manufacturers known to make perfect fans do not have a 30mm model, they start at 40mm.The 30mm one I got off of Amazon is crap and I had no idea which ones are good since they are all made by unknown brands.So I decided that I wanted to use a 40mm...

I did not integrate this into the grill itself as you might want to swap the location of the pi to either side based on your preference.I appreciate any tips to support my work!Print SettingsPrinter Brand:CrealityPrinter:Ender 3...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

9) Wire the power and sensor wires to the Adafruit Proto-Screwshield (Wingshield) using the 'Wiring' section (above) as a reference 10) Connect 5V power to the 2.1mm jack to be sure everything works as expected 11) Attach the front to the rear of the...

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------...

If the format you use is not yet in the downloads, let me know, I will create the models for it. Now print the test part (#0 testmodel) start with the smallest tollerance and try to push the test part over the profile, it should not go strongly...

- You can find a somewhat more detailed list of supplies in my Instructable: https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Any combination will do (as long as the driver is 4" or smaller so it fits the enclosure -...

Models intended to be part of the numbers node all begin with the prefix MMU.Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm.Assembly...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Please check the pictures to see what's in this kit.This set includes:- Mezzalfiend of the Gorge (6+6)- Gorge Imps (4+2)- Aamon on Daemonium Kerubim- Mephisto - the Daemon Smith - Lilith - the Matriarch- Astaroth the Soulforged- Daemon Siege Machine-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

As per my usual, each Zip file will contain the model un-based, based, and with supports. In order to keep files sizes down, I will no longer included the mirrored files for some of the linemen which you can easily do yourself in either the Chitubox...

3D printed parts: 8 brackets, remixed by me and provided here (original design: https://www.printables.com/model/200616-creality-ender-6-enclosure-top-cover-lid-2020-240m) 3 door handles (https://www.thingiverse.com/thing:4768759) Shortened spool...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

This version is included for those that want to create a custom playing field using other materials.Other Printing NotesWhile I was able to get pretty good results printing the sidewalls without supports, I did get better results adding a couple of...