ctc twinmaker 3d models

Standards for CTC 3D Printers

CTC-A13 SKR E3 Case

Prusa CTC E3D V6 Holder

CTC-A13 SKR E3 Case

CTC Printer Control Panel Switcher with Three Functionality Modes

Spool holder for the CTC Bizer or the Makerbot Replicator

CTC Spring Loaded \r\n\r\nTwo Precision Ball Bearings 8x3x4\r\n\r\n

Printers Support for CTC Printers Requires a Human Interface Feed Tube.

I crafted this component to seal off the gaps created by taking out my CTC buttons.

Shell Housing for Breakthrough at CTC Dual for a BEC Socket - Externally Attached Fan

CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853

A Tool for Cutting PTFE Tubes in the CTC Extruder. ... 33mm Length for Original Nozzle or Drilled MK8 Nozzle, or 24mm for MK8 Nozzle. Print Settings Printer: CTC Rafts: No Supports: No Resolution: 0.2 Infill: 20%

CTC Dual Spool Adapter for Lower Friction on 30 and 34mm Rods, Compatible with all 52mm Filament Spools. ... Printer Settings Printer: CTC Dual Rafts: Not Necessary Supports: Enabled Resolution: 0.2mm Infill: 10% Notes: Two Outer Shells

CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853

Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.

This is a remake of the CTC spool holder that came with the printer Its only one piece, no threads required. ... I have printed using ABS on the CTC replicator clone.

Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.

This mod converts the thing from Thingiverse (https://www.thingiverse.com/thing:1161013) into a Prusa-style CTC printer.

I trimmed down the edges slightly to ensure it would fit seamlessly onto my Custom Traveling Castle (CTC) build plate.

I designed this for my CTC dual extruder, but it might just as well fit a Wanhao 4s too.

To Enhance Cooling for CTC Printers: Installation Instructions. ...Fitting the Enhanced Cooler Unit with a Supportive Fan Design.

Insert filament holders into the 3 cm holes located at the rear of your CTC 3D printers.

Endstop assembly for the end switch mounted on the rear wall of the CTC to the Z-axis.

... machines. One has a longer cable than the other. This part is suitable for printers with the longer cable. If the cable on your ctc-10s is shorter you could use my other design which can be found here. ...https://www.thingiverse.com/thing:4923655

... CTC Printer On Its Pre-Drilled Holes (43.5mm Center To Center). Print Settings: Printer: CTC Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 50% Notes: Depending On How Good Your Printer Handles Overhang, Support Might Not Be Needed.

27 printed chain links\nPrint Settings\nPrinter model: CTC\nRafts: disabled\nSupports: not enabled\nResolution: set to 0.2mm\nInfill density: 10%

I'm a large CTC Drucker that has two big holes at the back for the filament rolls. ...This is the matching cover to close them up.

Supporting Filament for CTC Prusa I3. ... Two rings featuring a hole allow effortless insertion of filament into the extruder, preventing accidental ejection.

I crafted a personalized remix of Makken104's Ender 3 Fan Cover specifically tailored for the CTC A13 3D printer clone, ensuring seamless compatibility and optimal performance.

Modified the Anet A8 Z motor housing to be compatible with the CTC's plywood frame, which features smaller mounting hole diameters and shorter stepper motor screw lengths.