ctc prusa i3 3d models

After a year of hard work on my printer, while I was tightening the belt before a print, I heard a crack: the anchor foot near the screw had broken. Looking at the piece, I saw that with the tension (I hold the belt very tight when I press, instead I...

After completing the initial works, I discovered that my printer was not as precise as I had envisioned, so I set out to create a series of enhancements to refine its performance. The first step I took was to place it on a sturdy 10 mm plywood base...

After the initial prints, I noticed that my printer wasn't producing the level of precision I required. To address this issue, I developed a series of upgrades to enhance its performance. My first step was to mount it on a sturdy 10 mm plywood base...

I had printed a ventilation duct that I had found here on Thingiverse but I was not completely satisfied with it, taking the idea of having a light point near the nozzle, I designed a new one that divides the air flow in 3 directions in addition to...

My belt tensioning was busted and CTC didn't supply the STL file, so I fabricated it myself. ...Simple to 3D print and swap out!

My belt tensionnig was broken and CTC don't provide the stl file so I make it myself. ...Easy to print and change !

I rebuilt a new design that accommodates two bearings, specifically the popular 608 type. It can be paired with an 8mm shaft, which features a threaded connection suitable for various 8mm components. ...Don't worry about the image settings; I used...

I completely redesigned it to accommodate two bearings (608) now. ...Assemble it using an 8mm axle - I threaded it for that purpose, and you can also use any other 8mm component without worrying about the pictured settings; I was missing the 8mm bolt...

Are you struggling with wasted filament and time on printed projects? I faced the same dilemma, which led me to create a tool holder that requires only 9 meters of 1.75mm filament (approximately 29 grams or $0.60 worth of GreenTech filament) to keep...

After the initial projects I realized that my printer was not as precise as I had envisioned so I prepared a series of updates to enhance its performance. The first step was to place it on a 10mm plywood board and utilize this for the necessary...

I wanted to Mount my 18mm Capacitive Sensor directly to my Printer, but I was unable to locate any suitable spot due to the obstruction caused by my Duct Fan. This design proved to be the ideal solution, positioning the sensor close to the nozzle...

Adds bearings to the Z axis and fortifies it with standard abec skateboard bearings, available at an affordable price. Contact me for cheap options! To ensure a snug fit, wrap tape around the top of the threaded rods, eliminating any play. ...If you're...

Install a motor bracket that clicks into place on the y-axis with an infill percentage of 50%.

For a CTC Prusa i3 5MM Plywood Frame: Resolution: 0.30 millimeter

A Compact Kit for Mounting a Circular Tangential Fan on a CTC Prusa i3 3D Printer

This is a cover for the power supply unit for the CTC Prusa i3 Pro B 3D printer. Check your power supply dimensions. ...This cover will only fit for a power supply with the dimensions 96x42mm (w x h).

This protective casing is specifically designed to shield the Power Supply Unit of the CTC Prusa i3 Pro B 3D Printer. ...Before installation, verify that the Power Supply's measurements match the required specifications: a width of 96 millimeters and a...

A remarke with také for the limit switch and integrated M3 nut inserts for my ctc prusa i3 pro b.

Filament Leader for CTC DIY Prusa i3 5mm spacing to clip onto the frame at any desired location.

This is a complete CTC Prusa i3 frame. I designed it so all parts can be printed on a 150mm by 150mm bed, except for the 'Y Front' which needs to be 190mm long. All parts fit together using M3 nuts and screws. You'll need to print 18 separate...

This is a remix of the Geeetech/CTC Prusa I3 Pro B E3D V6 Extruder Bowden Adapter version 2.2 with a 12mm sensor holder. ...Y offsets are set at 23mm.

I'm not thrilled with the nut trap slot setup on my CTC Prusa i3 (plywood frame) either. The z motor mounts are built to be a lot more robust, and they bolt directly into the existing frame holes using a through bolt/nut combo - significantly...

This is a usable but haphazard creation tailored to the CTC Prusa i3. It's an amalgamation of https://www.thingiverse.com/thing:1694197 and http://www.thingiverse.com/thing:1369178, resulting in a somewhat unstable union. The latter item doesn't fit...

These are the supports that hold on the screen & memory card reader part of the CTC prusa I3 pro B to replace accidentally snapped ones. Freecad saves are included. Category: 3D Printer Parts

Here are the replacement parts for the CTC Prusa i3 Pro B's screen and memory card reader assembly, which holds everything together in place. ...Freecad design files are also provided for easy replacement.

Print Settings Printer: CTC Prusa i3 pro B Rafts: No Supports: Doesn't Matter Resolution: 0.2 Infill: 25-50% Notes: Before assembling all pieces, check them carefully to remove any potential strings or ringings; otherwise, the soft plywood may be...

This are some simple feet that I made for my CTC prusa i3, so can be easly atached to a support table. I had placed a pair of holes so every piece can be screwed, but by now i just had glued them and works perfect. ... All pieces has 0.2 mm tolerances.

Supporting Filament for CTC Prusa I3. ... Two rings featuring a hole allow effortless insertion of filament into the extruder, preventing accidental ejection.

This is a remix of [Cable Drag Chain 10x20 mm for R-CNC (Universal)](https://www.thingiverse.com/thing:2832548) I made these to fit my 10x20 drag chain onto my CTC Prusa i3 DIY printer. The design is similar to this one on Amazon. Nothing fancy...

... on the printhead. ...Print Settings Printer Manufacturer: RepRap Current Printer Model: CTC Prusa i3 Pro B Rafting Options: Disabled Support Structures: Not Required Layer Resolution: Set to Fine at 0.1 mm Infill Density: Configured for Moderate at 20%