ctc i3 pro 3d models

This is a configuration file for Klipper, an open-source firmware for 3D printers. The file appears to be specific to a CoreXY printer configuration and is tailored for use with an Arduino Mega (ATmega1280) microcontroller. Here's a breakdown of the...

I made another one, and this time it's bigger. I picked up some skills as I worked with 123Design, so I'm not starting from scratch. I simply drop a screw into the back hole and tighten it down. Update 8-26-17 I've upgraded Superstomper's foot by...

I made the one from John1h more stable and closed the holes near the Motor Holder. 12/2017 V2 Give a bit more room for the stepper Motor. I drill 4 Holes through the Panel and the Plywood, and mount it with M3 Screws. ... Thanks to @Pepcowboy and...

Small adapter to use M6 threaded rods in Z axis and replaces M8 lead nut, uses M6 nut and existing 4x M3 to mount it. Conversion: - Print 2x M6 Z adapter and put 2x M6 nuts inside (very tight), mount it to the existing X gantry (white PLA piece in...

Ensure the surface is immaculately smooth. Print two copies with mirror-image symmetry. This design was crafted with meticulous attention to detail. ...View the creation process here:...

This is a fusion of https://www.thingiverse.com/thing:1299185 and https://www.thingiverse.com/thing:1423957.\r\n\r\nI installed a straightforward 12-volt CPU fan and an inductive distance sensor (LJ18A3-8-Z/BX) on it.\r\n\r\nIt operates very well.

Lowered holders, rounded corners, reinforced upper surface.

I fixed this design: https://www.thingiverse.com/thing:2074071

The Prusa I3 Pro's Z-axis CTC replacement part is a total disaster from the start, featuring a flimsy plastic tube that's completely unacceptable ("WTF"). It's an absolute travesty that it even exists in its current form. ...The design calls for the...

It's specifically designed to be used in conjunction with the original CTC Z carriage plastic components. The carriages are simply resting on top of these parts, held in place by gravity alone. ...This setup also helps prevent severe nozzle crashes from...

This compact V-grooved bearing holder securely attaches to the top of the frame, expertly guiding the filament into the extruder. ...I'm using a 5mm frame, so I'll need to customize the slot size to perfectly match my frame's dimensions.

Created with TinkerCAD's innovative design capabilities, this custom mount empowers users to securely attach a 40mm radial fan directly to its front-facing surface. ...By seamlessly integrating with the original carriage, the mount provides a stable and...

This remix is designed to be printed without support. To create it, you can use the 2-in-1 fan from either Thingiverse's E3D V6 at https://www.thingiverse.com/thing:839620 or Thingiverse's E3D V6 Volcano at https://www.thingiverse.com/thing:1091522.

Hello everyone! Attached is a fusion of the best top mounts from both worlds! Now you can have more stability or a cable chain in one print. Matching other sides are attached above. ... Matteo1041 created the stability:...

This nozzle ring light was crafted for my CTC DIY i3 PRO printer and also fits seamlessly onto the Anet A8. It's secured via a screw that is already installed on the print head's underside. ...The LEDs used in this design are 12 white, 5mm units, with...

... ... For 12V, 15A Power Settings: Printer: CTC DIY Prusa i3 Pro Rafts: Don't worry about it Supports: No need for any Notes: When you use this setup, make sure the power connector is facing downwards. Extend the earth wire to ensure safe operation.

Designed with Catia printed in ABS for Prusa i3 Pro B ctc Print Settings: Printer Brand: 3D Systems Printer: CubePro Rafts: No Supports: No Resolution: 0.4 Infill: 60% Notes: ABS or PLA Post-Printing How I Designed This with Catia Standards: NGSS...

You can reuse your Prusa I3 PRO (CTC version)'s original limit switch and screws.\r\nThe middle hole accommodates 8mm unthreaded bars perfectly.\r\nThis accessory is specifically designed to fit a 20x10.5x6.2mm Limit switch, with precise measurements...

My belt tensioning was busted and CTC didn't supply the STL file, so I fabricated it myself. ...Simple to 3D print and swap out!

My belt tensionnig was broken and CTC don't provide the stl file so I make it myself. ...Easy to print and change !

I have increased the frame slot to accommodate a printer using an 8MM frame: the Geeetech i3 Pro B and Pro C. I have used this brace for over a year now and it has greatly helped stiffen the frame on my printer, allowing faster speeds. You will...

Install a motor bracket that clicks into place on the y-axis with an infill percentage of 50%.

Are you struggling with wasted filament and time on printed projects? I faced the same dilemma, which led me to create a tool holder that requires only 9 meters of 1.75mm filament (approximately 29 grams or $0.60 worth of GreenTech filament) to keep...

This is a cover for the power supply unit for the CTC Prusa i3 Pro B 3D printer. Check your power supply dimensions. ...This cover will only fit for a power supply with the dimensions 96x42mm (w x h).

Improvement of upper support for CTC i3 pro b. Increased guiding area. ...For the other side, do a mirror in cure.

The design is based on the authentic mount plate for the Y stepper motor found in the CTC i3 Pro B 3D printer. ...The model was crafted using precise measurements from a genuine replacement component.

This protective casing is specifically designed to shield the Power Supply Unit of the CTC Prusa i3 Pro B 3D Printer. ...Before installation, verify that the Power Supply's measurements match the required specifications: a width of 96 millimeters and a...

... position. No extra hardware is required since it uses the same screws provided with the printer. The design incorporates the axle part from the original spool holder that comes bundled with the CTC i3 Pro B, ensuring a seamless integration.

... ...I am using a CTC i3 Pro, but its LCD Rear is too small to support the standard brace. ...To make up for this limitation, I designed and printed a new LCD Rear that also serves as an extension for the original spool holder.

This is my take on the belt mounts/tensioner on the CTC I3 Pro B. It's specifically designed for GT2 20T Idlers with 5mm ID bearings. To assemble it, you'll need a countersunk M5 16mm screw, an idler, and a M5 square nut. Mounting requires a M3...