ctc i3 pro 3d models

I had printed a ventilation duct that I had found here on Thingiverse but I was not completely satisfied with it, taking the idea of having a light point near the nozzle, I designed a new one that divides the air flow in 3 directions in addition to...

When the new printer arrived, I noticed that the Y-axis was extremely unstable. To address this issue, I re-designed the mount to accommodate the smaller shaft size of the Y-axis. ...The original mount had a 10mm hole, but the shaft itself is only 8mm...

This LM8UU Holder seamlessly replaces outdated heatbed bearing holders, ensuring a seamless transition without necessitating any additional hole drilling. Secure it firmly to the base plate using M3 screws for maximum stability. ...Crafted from PLA, yet...

Not much of a remix, but am including both Left and Right brackets with support brace

This model was designed using Tinkercad's user-friendly platform. ...Make your modifications directly within the browser at https://v1.tinkercad.com/things/gKmu6oqjHWG.

This sleek new belt holder takes its place alongside the old wooden one, which was deemed unstable and cumbersome. ...To secure it in position, simply utilize the pre-existing M3 screws and nuts that will be threaded into the base plate with ease.

After the initial prints, I noticed that my printer wasn't producing the level of precision I required. To address this issue, I developed a series of upgrades to enhance its performance. My first step was to mount it on a sturdy 10 mm plywood base...

Just another enthusiast of extruders, but this time I'm focusing on a 60-millimeter model.

Design is intended to accommodate a 50mm radial fan, the kind that can be sourced on eBay. All models were created using millimeters for units and modeled at ten times scale, so set the scale to 10% in your slicer of choice. Some parts are designed...

I wanted to relocate the inductive sensor to the front and left side of the device, directly adjacent to the fan mounting bracket, so I modified the design to meet my specific requirements. ...The original blueprint can be found on Thingiverse at...

After completing the initial works, I discovered that my printer was not as precise as I had envisioned, so I set out to create a series of enhancements to refine its performance. The first step I took was to place it on a sturdy 10 mm plywood base...

After a year of hard work on my printer, while I was tightening the belt before a print, I heard a crack: the anchor foot near the screw had broken. Looking at the piece, I saw that with the tension (I hold the belt very tight when I press, instead I...

This is a remix of tom666's MK8 Extruder Upgrade. I really liked that upgrade, one of the first things I had to print, and used it until I wanted to print flexible material. The extruder gear just rolled the filament up inside. It's basically the...

This is a remix of the awesome AM8 frame by pheneeny (https://www.thingiverse.com/thing:2263216) , I found that the CTC Pro I3 B (or whatever its called this week as the name changes frequently) does not share all the same parts as the Anet A8 this...

This is a remix of the awesome AM8 frame by pheneeny (https://www.thingiverse.com/thing:2263216) , I found that the CTC Pro I3 B (or whatever its called this week as the name changes frequently) does not share all the same parts as the Anet A8 this...

Please keep in mind that this modification is specifically designed for the CTC Prusa i3 DIY Clone and requires upgrading the firmware to use the 3DTouch feature. ...I'm currently running Marlin v1.1.4, but you can ask if you need assistance finding...

This clip allows for a straightforward reversal of the x-axis endstop. ...Simply attach it to the existing CTC bracket and you're good to go.

This is part of my continuing quest to make this cheap junk CTC printer work properly. It has made an absolutely massive improvement! The original printer used some 3D printed sleeves with a small brass collar inside them, and used cable-ties to...

This is part of my continuing quest to make this cheap junk CTC printer work properly. It has made an absolutely massive improvement! The original printer used some 3D printed sleeves with a small brass collar inside them, and used cable-ties to...

The Prusa i3 Pro CTC requires a fan and probe mount, which necessitates some M3 nuts and screws.

1x M6x6 countersink screws (base) 1x M3x18 countersink screws from the original extruder (lever) 1x M10x6 countersink screws (bearing) 2x M3 washer (bearing) spring (thickness 0.8mm, inner diameter 6mm, outside diameter 8mm, height 18mm) bearing from...

... 50 mm, ventilator breath on the side. Ref : B5015L12C de T&T https://www.dealabs.com/forums/le-bar/le-laboratoire-high-tech--informatique/ctc-prusa-i3/25480?page=36#comment_684838 We can cover the dissipator, or use another 40 mm fan and more.

**Flashing Firmware**: The instructions provided for flashing firmware using avrdude are specific to the AVR atmega1280 processor and highlight the need for precise configuration when working with custom or specialized boards like the CTC Prusa i3...

This is a versatile 3D printed spool holder compatible with various 3D printers, including the Prusa i3 Pro B model. It cleverly utilizes the plastic component of an old spool holder, easily snapping into place just like its predecessor. The design...

... in the .scad file accordingly. Print Settings: Printer: Ctc Prusa i3 variant Rafts: No Supports: No Resolution: .3 or .2 Infill: 40% Notes: Print with at least three outlines. ...Fan cooling for holes is recommended but not strictly necessary.

BOM: * 1x M3x6 countersink screws (base) * 1x M3x18 countersink screws from the original extruder (lever) * 1x M3x10 countersink screws (bearing) * 2x M3 washer (bearing) * spring (thickness 1.2mm, inner diameter 6mm, outside diameter 9mm, height...

I was approached by a member of the CTC group on Facebook to adjust the original Joox design for the new 6mm Frame version. A test print in 6mm has been included, allowing users to check fitment before proceeding. UPDATE: On March 1st, 2018, it was...

I inset the clamp mounting screw head holes and their associated nut holes to allow "extra" plywood frame assembly screws that usually come with the CTC Prusa clone to be used. Included is the butchered .scad file for anyone who wants to butcher it...

Prusa i3 users rejoice! Introducing the BLTouch Mount, specifically designed for your beloved 3D printer. This sleek and sturdy mount provides a seamless integration of the BLTouch sensor, ensuring accurate and reliable prints every time. With its...

... LCD until you get the nozzle in the correct location (mine was -0.25). * Save your settings. By following these steps, you should be able to upgrade your GEEETECH Prusa i3 printer's firmware to Marlin and enjoy improved performance and features.