ctc a13 printer 3d models
398751 3d models found related to ctc a13 printer.
thingiverse
... at this point. ... So I modified the original plate and everything is fine now. Info: Printer: Prusa i2 Nozzle diameter: 0.5mm Layer height: 0.3mm (filament width 0.35mm) Material: ABS Infill (set by slicer): 40% (but lower percentages also work)
thingiverse
I designed this crucial component due to the upgrade that came with my 3D printer, as well as its Anet electronics and wooden frame, which differ from standard designs. The limit switch, responsible for restricting motor movement in the extruder, was...
pinshape
The Pivoting Arm Was Made Even Thinner at the Top to Ensure Compatibility with All Printer Versions, Especially Those with a Cover on Top of the Extruder Motors. 2. The V-Groove Gear Now Fits Easier Inside the Arm, Requiring Less Post-Print Work, and...
cults3d
It should fit many different printers, but I designed it for my Replicator-Clone. The Fan controller I used was the Aerocool F5XT:http://www.aerocool.com.tw/en/fan-controller/single-bay/f5xt The circuit board can be loosened very easy and the...
myminifactory
This setup should fit various printers, but it was specifically created for my Replicator-Clone. The Aerocool F5XT fan controller, available at http://www.aerocool.com.tw/en/fan-controller/single-bay/f5xt, was used in this project. The circuit board...
thingiverse
To craft a sturdy camera mount resembling the letter "H", one requires 11.5mm aluminum tubes and a set of screws. ...The design calls for creating two identical units, while only producing one camera base unit.
thingiverse
This model was created using Tinkercad's powerful tools. ...Edit it directly online at https://www.tinkercad.com/things/5X6tO4rBmC1
thingiverse
This LED holder attaches securely to the X-axis via clips. It serves as a carrier for 24-volt LED strips, easily positionable at both the front and rear of the axis. With 24-volt LEDs onboard, the device can be directly connected to a power supply...
thingiverse
My revised rendition of an A13 Mk2 is now available for your review and consideration.
thingiverse
This is a standout case for the Olimex A13 OLinuXino.\ Grab one now: http://builttospecstore.storenvy.com/collections/13701-all-products/products/9161182-olimex-a13-olinuxino-case\nFull setup directions are...
grabcad
This is a 3D render of Door A13, offering a detailed visual representation of its design and features.
cults3d
... Follow full assembly instructions here: http://www.built-to-spec.com/blog/kit-instructions/a13-olinuxino-enclosure-assembly-instructions/. ...Designed by RoboLemur.
thingiverse
Cover for CTC 'large' LCD panel backside used in a 3D printer. This design won't fit on the Dual Size CTC model with dimensions 175 mm x 80 mm x 3 mm. ... Mounting: The cover simply clicks into place over the circuit board spacer.
thingiverse
... cases that are 5mm thick too. It's great for printing PLA, but it's not ideal for ABS! Check out the attached PDF to make sure it fits perfectly on your fan or case. Print Settings Printer: CTC Rafts: No Supports: Yes Resolution: .2 Infill: 25
thingiverse
Simply print the appropriate spacer and pop it over where the Z stop contacts your bed assembly.\nThis is easy stuff!\nPrint Settings\nPrinter: \n CTC printer\n \n Rafts: \n disabled\n \n Supports: \n turned off\n \n Resolution: \n 0.3 millimeters\n...
thingiverse
This modified design is specifically for the CTC I3 eBay printer power supply. If you're stripping it down to convert into a Prusa MK2 clone due to its inherent build issues, you'll need this custom PSU holder as the Prusa uses a different one...
thingiverse
I designed an LCD 12864 Mount for CTC FlashForge or Makerbot. I built this when I upgraded my mightyboard to RUMBA for a diamond hotend. ... The mount is constructed from three components: Cover --- obudowa_LCD.STL Reset Button --- ...
thingiverse
It took me 2 printers to figure this out - one set of rods didn't require any adjustments, but the other needed drilling with a 5/16-inch bit. Alternatively, you can get metric bushings, but be warned they cost three times as much. Drilling to ream...
thingiverse
Stand for the print head for a 12V LED bulb (T5) available in a car shop
grabcad
A big thank you goes out to my buddy, Manolo, who played an instrumental role in our collaborative efforts within the field of engineering.
thingiverse
For optimal results, ensure that your spacer is positioned upwards. If laid flat, it won't yield a satisfactory print. ...I opted for ABS in my build, but PLA can serve as a suitable alternative with identical performance.
thingiverse
Sometimes it's very helpful to be able to adjust the z-axis manually. Range: -6 mm (be careful) +9mm You'll need: The two plastic parts 2x M3 square nuts M3 threaded rod, approximately 100mm long 2x 3mm steel shafts, approximately 5mm long (or 3mm...
thingiverse
The A13-OLinuXino development case is both straightforward and productive. ...To obtain the design, visit its GitHub repository at this link: https://github.com/worldline/A13-OLinuXino-case
thingiverse
A joystick sleeve for the stock stick on a Powkiddy A13. Should work on the A12 as well. This will allow you to attach the joystick and play without it unscrewing. ...Won't fit into the storage tray without modification.
thingiverse
This is a stand specific for Galazy A13 phone, but it will hold many other makes and models with protective cases. The tray is for double sided tape to be mounted to a moving cart, yet still allow the stand to be moved about when needed. ... Its a...