ctc a13 printer 3d models

Originaly designed for my CTC printer (clone of the ender3 but way too bad product)

I crafted a personalized remix of Makken104's Ender 3 Fan Cover specifically tailored for the CTC A13 3D printer clone, ensuring seamless compatibility and optimal performance.

Fixation for the Heatbed Cables of Your CTC A13 Printer is Easy! Simply Secure It at the Left Rear Screw of the Heatbed and Keep Cables Organized with a Cable Tie. ... Two Options Available: One Requires Support, While the Other Can Be Printed Without.

This part is a back cover for the LCD control module of a CTC A13 printer. The screw holes and ribbon connector cut-outs match the CTC A13 control unit. ...Long screws may be required to attach the cover to the front plate.

... filament roller tabs. ... The micro switch body is 20 x 10 x 6.5 The bearing used is 8mm ID & 16mm OD Based on the design posted by Caipi and completely remodelled to suit my CTC A13 printer but can also be used on Ender 3 or CR 10 and other clones.

If you have a CTC A13 printer you will know by now that the build quality is very poor. One of the first parts to break on my printer was the spool holder. I printed the excellent Ball Bearing Spool Holder designed by vivamus3d on Thingiverse:...

Feet for CTC A13. ... Front feet screw on with stock screws, I used a hammer to get the back feet on then stuck the rubber 'feet' that came with the printer back on these.

Human: Feet for CTC A13. I attached the front feet using the original screws provided, but had to apply some force with a hammer to secure the back feet. ...I then replaced the rubber pads that came with the printer onto the newly installed feet.

CTC-A13 SKR E3 Case

CTC-A13 SKR E3 Case

Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.

Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.

CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853

CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853

One of the first parts to break on my A13 printer was the spool holder. I printed the excellent Ball Bearing Spool Holder posted by vivamus3d on Thingiverse: https://www.thingiverse.com/thing:4576421 . The problem is that the pressed steel spool...

This adapter connects to the gantry on my A13 printer and then converts into a 209mm center-spaced mounting system. I have also included an STL of the adapter so it can be printed if required; however, I had no need to print it as I could laser cut...

I couldn't locate the specific component I needed for my CTC A13 Ender 3 Clone, so I chose to create a custom version instead. ...Hopefully, someone with this printer will be able to utilize my design and make some improvements to it as well.

Changed the Click part to fit on a CTC-A13. ...

This part is based on other tool holders uploaded for the Ender 3. ... I allows the storage of all of the A-13 tools.

To achieve better stabilization of CTC printers.

Having to feed filament from below my printer led me to make some adjustments, so it meets my specific needs. I also incorporated a dust filter, inspired by another popular model, thing:2349995, which is designed to capture debris and keep my...

Door hinges for the CTC 3D Printer. A bit of an unassuming upgrade... ...You'll also need four M3 x 40mm screws.

Printing small feet for the CTC 3D Printer can significantly reduce noise levels, especially when combined with rubber pads. To achieve this, print the left foot twice and the right foot twice. ...The recommended settings are a layer height of 0.2mm and...

I have designed a larger tool holder for the CTC 3D printer with a 5mm frame. ...The tool holder has a compartment for a knife or small spatula, two compartments for USB sticks, four holes for screwdrivers or pens, five compartments for SD cards, and...

The CTC 3D Printer receives an upgrade to refine its appearance. This design draws inspiration from the Thingiverse model at http://www.thingaverse.com/thing:559387. Printed settings include a layer height of 0.2mm and infill percentage of 10%. ...The...

... the wood case or drill it larger and use washers and nuts. Following settings worked fine for me on a CTC printer. ... PLA Filament 230°C Nozzle / 120°C Heat bed (blue taped) 3 Shells / 15% Infill 0.1mm Layer height 130mm/s speed while extruding

The basic CTC printer guide features a simple yet effective design, utilizing the standard tubes supplied with the device to direct the filament. This ensures it stays centered at all times, preventing it from drifting to one side as it's pulled...

This CTC 3D printer has a robust 5mm wooden casing surrounding its metal frame, offering a durable base for operation and assembly on any surface. ... To secure this attachment to your 3D printer's back side, simply attach the Holder with clips or...

Print Settings Printer: CTC Bizer Rafts: No Supports: No Resolution: 0.2mm Infill: 30% Notes: Printed in PLA at 220C with 50C bed Custom Section UPDATE:1 I installed an RGB LED strip on the printer to illuminate the build area, but the mighty board...

I print slowly, using 0.3 layer height with a raft on my CTC 3D printer because it's not built for high-speed printing. A 22mm PVC pipe section is required to span the top of your printer in this design. If you find any issues, please contact me...