csx printers 3d models

Protective face shield designed for 150mm x 150mm printers. Uses clear sheet with 3-hole punch. ...Top cover Add-On by Sophy Wong's Add-On <a href="https://sophywong.com/addon">https://sophywong.com/addon</a></p>

This is a remix of Jsalin's work, and I'd like to acknowledge his contribution. ...To make the design more printer-friendly, I've broken it down into four sections that can be easily printed in parts.

Wanted a way to mount a SKR Pico in an Ender 5 and Ender 3 so this little bracket will let you mount the SKR Pico in most Creality printers.

This is a remix of the original Greek Meander Lamp by Hultis. ...https://www.thingiverse.com/thing:3434805 I just split the huge parts of this cube, to enable printing with small printers, like Ender 2.

I decided to split the hat in three parts for one color printers. Insert band in the top part and glue it to the bottom part. ...That's it !

I disconnected the power conduit by dividing the wireway in two sections using 3D modeling software, allowing me to produce a printable component for my Printrbot Simple Metal 3D printer.

Only required screws are two M3x12mm and nuts for clamping the groove mount. ...The mount uses the existing screws to attach to the printer. ... Optional mounts are available for BLTouch and EZABL probes.

So I was about to 3D print something once but then I couldn't find my SD card. ...So I had to buy a new one. Then I just made an SD card holder for my 3d printer.

Laptop Protable Suitcase used to carry Laptop printers and manymoreEasy for office useFor any help then connect with meLinkedIn: https://www.linkedin.com/in/ashish-palankar-62a8291aa/Gmail: designwithashish18@gmail.comFiverr:...

I've also included a presupported version.&nbsp;&nbsp;This should be helpful for determining if your printer is printing properly in the XYZ. ...When Measured each side should be 20mm&nbsp;</p>

Cut down in size for printing multiple pieces on any 220mm x 220mm printer, I noticed Thingiverse lacked micro ATX mobo trays suitable for smaller printers. This design prints perfectly on an Ender 3, taking nearly 9 hours to complete. The tray...

This is a REMIX of https://www.thingiverse.com/thing:4006164 I divided the headphone holder for smaller printers into 3 parts. ... I also made them a bit taller so that large headphones don't hit the table.

We need a new tool for scraping off completed prints from our printer. ...Ideally, this tool should have a wider head to clear more surface area at once, and a shorter handle for improved balance and control.

If you have a DaVinci printer that uses proprietary cartridges and you've managed to get rid of those cartridges by using a special device that makes your printer compatible with all PLA/ABS filament on the market, this might be useful for you. I am...

I decided to split the hat in three parts for one color printers. Insert band in the top part and glue it to the bottom part. ...That's it !</p> Category: Art

This design adapts for FelixRobotics Felix 3D printers (v1.0-3.0), originally crafted for the OpenBeam KosselPro printer: https://www.youmagine.com/designs/filament-spool-holder-for-openbeam-kossel-pro The central components are two cones running on...

The text describes a component designed specifically for usage with RoBo3D printers, featuring a 8mm mounting hole for the DI and two 6x5mm magnet slots. ...Some adjustments to the holes might be necessary.

The original design in https://www.thingiverse.com/thing:3543804 had one of the trays (Other Tiles) too large to fit in Ender 3 printers. ...I separated the tray in 4 parts that can be glued together.

SImple Compensation Test for 3D Printers. Adjust the horizontal compensation in your slicer accordingly. print .2 with min 20% infill.use calipers and the diagram to cross-reference theoretical dimensions and real dimensions. ...(reference sketch for...

... for on the printed t-nut if you decide to print that. While these are originally for the Thinker printers, I'm sure you can use them for other printers using aluminum extrusions.. you'll just need to scale the z height to fit your printer. ...

Can lid for dual color printers. ... Can lid for single extruder v.2: https://www.thingiverse.com/thing:5391206 Can lid for single extruder v.1: https://www.thingiverse.com/thing:3759439

Loved the design of the mask, but couldn't get it to fit on my printer. ...Figured I'd upload the split apart version for those who can't split it apart themselves for whatever reason.

I Design a Special Cube for Two-Color Printers. Instead of counting numbers, I'll simply measure the number of polyhedra formed by my cuts. ...My instructions are clear: cut the cube precisely three times with a flat surface.

The Ultimate Starter Kit for Your First 3D Printer - A 20mm³ Calibration Cube \r\n\r\nEngineered with Precision using Autodesk Fusion 360 Technology \r\n\r\nAvailable in Both .STL and .F3D File Formats

In the event your printer encounters difficulties with part '1', consider trying out the alternatives that include an integrated base - this base can be removed easily after printing is complete. ...Additionally, I've included a convenient connector...

... the bar to the frame, ensuring a sturdy hold. If you're seeking alternatives, high-quality 12mm aluminum chromed tubes offer excellent options - they are lightweight, robust, and remarkably rigid, providing optimal support for your 3D printer.

... right hand side. After homing the printer disable motors and pull it tigt against the block on the right side, voila your printer is aligned perfectly Instructions this part is made in autodesk inventor to fix my claibration issues with the y axis

... adaptable to any CoreXY printer configuration. Key Features: * Enhanced nozzle wipe system using silicone inserts for improved performance * Customizable design for seamless integration with various printer profiles, including the 2020 profile

Check out this video to see exactly what I mean.\r\nThis was tailored specifically for my remote shutter and 3D printer, but I'm hoping it inspires people to customize the design for their own gear. ...If you're a 3D printer owner, you should definitely...

the Prusa Mini. This fits nicely over a standard Bowden tube, if you need to change the size, you can either use sandpaper or modify the attached Fusion360 file. After a few prints, maybe 300g of PETG, the filter has already removed a significant...