crystal peak mine 3d models

Mine didn't came out great because of that, but yours can. - A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin) ## Print orientations Case...

Thanks CFox! This is the new file:internal-608-roller-bearing-base-adapter-for-newer-printers-1.0.stlI've you're using an older printer like mine in the pictures, print this...

O-rings I got mine on Amazon as follows: 031 Silicone O-Ring, 70A Durometer, Red, 1-3/4" ID, 1-7/8" OD, 1/16" Width (Pack of 25) https://www.amazon.com/gp/product/B000FMYO6Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 023 Silicone O-Ring, 70A...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

The Fan connector on mine actually would fit through sideways, and the Extruder Motor connector wouldn't quite fit, but I flexed the plastic and got it through. You also have the option of unscrewing these and reattaching them on the other side. I...

Behind this is a small project of mine, in the course of which I want to cram as many sensors, actuators and breakboards for the Arduino into a housing as possible. Plus a 7 inch touch screen and lots of communication interfaces. Why? I might tell in...

I used wood screws to mount mine. Any wood screws will work, just make sure they fit in the slotted holes so the plastic doesn't bust. You don't have to mount it yet, but partial disassembly will be needed to mount later. 12. Using 4 (1/2...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

Mine had somehow drifted over time due to loose screws, because of which I wasted some time in understanding why my X carriage didn't move freely and was wobbling a bit. After meticulously squaring the frame, the problem was resolved. **Mandatory...

I have mine in an enclosure and only have them printed in PETG instead of ABS or stronger. So I have experienced some issues over time with these due to the heat. I changed the slots used for mounting to the linear guide block to holes and beefed...

They can be mounted with stock components, or with another work of mine, the "anti Z wobble" inspired by HEVORT (I put the link at the bottom of the article). The attachments are fixed to the aluminum profile of the X axis with 4 M5 12mm screws and...

:) I included the modified STLs I used to make mine, basically smaller versions of DIY-Machines version and more of them and I added separate diffusers instead of his multi-filament versions, so that they can be printed on my smaller single-color 3D...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

I think mine were roughly 9 inches/22 cm; longer is easier to work withCut a small length of aluminum wire and wrap around the center (this is just to hold everything together temporarilyCut another length of the black nylon thread, exact length...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of...

Update 2 (2018-02-24): I've been musing about the z>160mm problem for chains that don't coil perfectly like mine (see update 1 above). I considered several approaches, but ended up with the most simple one: a fence which keeps the chain from...

Unfortunately I sourced mine locally so I can't link to it. You need a minimum of 3 pieces (or one larger) with a dimension of about 40 x 50 cm each. One of these should be enough to cover all panels but I haven't tested this one in particular...

------------------------------------ ENGLISH ---------------------------------------------The guide was translated using google, I apologize in advance for any errorsTo conclude the set of linear guides on the X1, this time I propose some attachments...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...

Length was chosen to match the width of the printer (mine is 438mm). K1's have a width of 335mm to 355mm depending on revision, so that's the length of extrusions for them - please measure your machine before ordering/cutting the extrusions.The...

All other mods (uprights, tensioners, fan duckt) you can see on screen are not mine, but i can link them if there is enough interest. WARNING!!! THIS IS NOT A SIMPLE PROJECT! DISASSEMBLE YOUR PRINTER AT YOUR OWN RISK! I AM NOT RESPONSIBLE FOR...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-180B is approved for use within environments where flammable or combustible...

Mine are 25mm, for example, the Cross Country Performance kit uses 30mm thick spacers so you could modify the height in the Z-Axis in your slicer to potentially get 2.5" of lift from the tophat spacers alone. <b> Rear spring spacers only and front...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

If they are too loose, you can glue them in with CA glue.The gears need to spin freely on the metal shafts, mine worked fine right off the printer. You can drill them out with an 1/16" drill bit if needed (use the included drilling jig to make sure...

I printed mine in PLA with 7% infill, 2 perimeters, and 0.2 mm layer height. The filament I used was scavenged from a dumpster. ## Assembly Notes In general, there's only one way for pieces to fit together, so it should be fairly intuitive how...

- if there is a fit issue (I had to change the dimension thickness of the chassis) hot water bend these to fit but mine fit perfect Lower box and rod - No support needed - 20 minute print - free mount for the base of the box, the rod will connect to...

Some of mine did not work anymore after these steps. Heating the contacts of the resistor solved the problem in my case.</p> <p>Insert the<em>Button Top</em>s into the<em>Front Panel</em> and mount the<em>Button Housing</em>s. Same goes for...

Notice: I have flipped the plate from its stock orientation to allow for a larger stepper motor, as I replaced mine. Replacing the motor is completely optional, but make sure to watch out for the orientation.</p><figure class="image"><img...