crv phone mount 3d models
394935 3d models found related to crv phone mount.thingiverse
Needed a phone mount for a 2019 Honda CRV and my OnePlus 7 Pro. Commercial options were $80+, and this was clearly a financial situation a 3D printer could solve. 5, 10, and 15 degree standoffs are included for custom viewing angles. Designing a...
thingiverse
This is designed to replace the factory switch blanks in the dash of a 2002-2006 Honda CRV, for the purposes of mounting an auxiliary switch for things like light bars, fans, etc. ...This is a flat blank which will mount flush with the dash in flat...
thingiverse
Recently, I purchased a 2018 Honda CRV but hated both available mounts, so I designed my own in Fusion 360. I was learning Fusion 360 at the same time which is why there are two design methods (split and All-In-One). ... The second AIO design has a...
thingiverse
This is a cell phone holder for a Samsung Note 8 and a 2020 Honda CRV EX-L. With a phone in the holder it does block the hazard light switch but removing the phone gives you access to the switch. It also allows air from the vents to get to the phone...
thingiverse
Car (2006 Honda CRV) had a dummy mount for XM, and the factory antenna is not made any more. This fits a Sirius XM SV300 antenna, and bolts directly to the holes in the roof of the car. ...Uses M4 bolts and screws into the plastic.
thingiverse
Printed these to replace speakers on my gf's CRV. ...I didn't quite get everything perfect but I made these work.
thingiverse
This is a mobile phone holder designed specifically to fit into the Honda CRV cup holders. It includes holes for threading a USB charging cable into the base. I've printed it successfully using both PLA and ABS. Some supports will be needed, but...
thingiverse
Frame to adapt 6-inch speaker for honda CRV 2008-2011
thingiverse
Broken mounting tab replacement for tweeter surrounds on 1st gen CRV's (97-01). Prep the area for repair by lightly sanding, then clean with an alcohol pad and let dry. Use a good plastic bonder to adhere the repair to the surround. ...Recommend using...
thingiverse
this is a phone mount for camera tripod for a phone with thickness of 1cm or less but you can scale it up for a bigger phone
grabcad
3D printed Go Pro mounted S7 phone holder, printed on my Form Labs Form 2 printer
thingiverse
This was a phone mount I created and it fits about any phone on the market and can even probably fit your phone case too! ...Fits a good selection of screws that could drill into a 2 by 4.
thingiverse
Mount was designed to be used with a vent mount style phone holder. ...Designed for use with aftermarket radio kit for a ford, may fit others.
grabcad
The Phone Mount allows for the phone to rest on the slanted base of the mount. The mount holds up the phone by little arcs towards the bottom. A little break between the arcs allows for the charger cord to access the port to charge the phone which...
thingiverse
A generic phone mount with screw attachment for universal mounting. By default this design comes with a mic stand adapter, and I'm working on a car adapter. The phone is attached to the adapter with a single M3 screw so the adapter should incorporate...
grabcad
The mount is designed so your phone can simply slide in and out of the mount freely and the mount is very easy to use. The mount would be constructed out of plastic and be able to be 3D printed and easily assembled. It can also be removed and the...
grabcad
The mount is designed so your phone can simply slide in and out of the mount freely and the mount is very easy to use. The mount would be constructed out of plastic and be able to be 3D printed and easily assembled. It can also be removed and the...
cults3d
Phone Mount with G-Clamp and full rotation. ...no screws required Remix from : https://www.thingiverse.com/thing:2809416 https://www.thingiverse.com/thing:1673030 https://www.thingiverse.com/thing:2448971
thingiverse
Phone Mount with G-Clamp and full rotation. ... no screws required Remix from : https://www.thingiverse.com/thing:2809416 https://www.thingiverse.com/thing:1673030 https://www.thingiverse.com/thing:2448971
thingiverse
Made this cell phone handlebar mount for a family member. He sketched out what he wanted on a scrap of paper and I made it come to life. Models include different length arms to account for different sized phones. Also includes a few different sized...
myminifactory
A handy removable change holder that fits nicely into the compartment under the armrest of a Honda CRV mk4.