crossbow drawing 3d models

You do have to be quite careful about the power draw. This many DotStars will consume around 2 Amps at full intensity, which is too much to pull through a typical USB hub when debugging with the computer attached. I put some compile-time switches...

This fixture is designed for mounting to high bay and wall I-beams.***PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO THIS HAZARDOUS LOCATION LIGHT FIXTURE***This Class 1 Division 1 & 2, Class 2 Division 1 & 2 explosion proof light...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The BoM below lists the least expensive option I could find for just these four screws.Sherpa Notes:I found that while the Sherpa Micro drawings call for shorter 4mm long M3 Brass inserts, that larger diameter 5.7mm long inserts fit better (see BoM...

This will reduce the intensity and dot diameter.Adjust the set screws till the laser does not draw a circle when you put it in the spindle and turn it by hand. You can also do this with a hand drill which turns slowly. Dont' be tempted to turn it on...

Then I tried to draw it and look that even taking into account the measurements, the angles... there was no way that the vertices would coincide well. So I went to do it in AutoCAD. What is happening, that I learned with the classic view and had not...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

Holster was ispired by youtube video: https://www.youtube.com/watch?v=67tAWwU9fT0 and this holster: https://www.thingiverse.com/thing:3934215 I started remixing the above holster, but ended drawing my own from the scratch. Parts are unified for...

The PI Uses the same pins as the PRUSA MCU and thus will not work-Uses 5V WS2812 Individually Addressable LEDs-Compiled with the Arduino FastLED libray-Max current draw ~300 mA Mandatory Parts list: Arduino Nano Individually Addressable LED...

[This project is still being actively printed, I will update this model with pictures, & upload remixes as I go through the iterative process.Update May 13th 2022: modified shelf hinge diameter to better slide on the poles, added drawing for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Multimedia Center for Raspberry Pi4 with Box for 5inch DSI touchscreen display or Monitor/TV and OMSC: 05/10/2023: - added PCB_Fan Regulator (thanks Cornflakesninja!https://www.thingiverse.com/thing:4121604) - redesigned Case...

An iconic presence in a city of architectural icons, the John Hancock Center rises boldly from the mid-American prairie to cast a cultural shadow much larger than the one it gets from the sun. It is a staple of movies, television newscasts, t-shirts,...

Please excuse my poor drawing skills.Mount the drill guides on the current Y plate. Notice: I have flipped the plate from its stock orientation to allow for a larger stepper motor, as I replaced mine. Replacing the motor is completely optional, but...

Per the drawing we will be using GPIO 18, 23, 24, and 25. Each to control a channel. Most of you would really only need two, one for a light and one for power. In that case just use 18 and 23. Assemble the Raspberry pi, wires, camera cable and SD...

For most signs, 5 is enough, but setting it higher has no adverse effect.How I Created The Room SignsThe text, the rounded rectangular base and the rounded square around the pictogram were created with OpenSCAD.The pictograms were created with Gimp...

I'm running the fan at between 7 and 9 volt - where it draws less than 400mA (though about 50% more on startup - which is to be expected). If I decide to drive it harder, I will connect it to a more robust power supply and voltage controller which I...

I added a button for manual activation but that was mainly used during the testing phase and I would maybe keep it for the occasional bug where the device doesn't perform exactly as expected.One important thing to note is that the servo will draw...

(reverse the taper direction so it gets wider further in, this can be a little confusing, so keep notes for clarity's sake, don't be afraid to draw a rough picture, it WILL help you). Remember to deduct the wall thickness TWICE from BOTH the "wider"...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

 They are now posted as well and are in a folder named “TOP DOOR PARTS”. Update 12/4/2023 - Apologies, I was looking over this model today and noticed that the draw latch parts were missing.  I have since uploaded them in the folder named “Latch...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I have included a drawing of the front opening and mounting holes. Most 4" drivers should fit. If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit...

These pieces have nice, large solder pads for easy work. External Parts Needed* ========================= USB C Charger...

The EPL-LP-2X48-LED is equipped with terminal strips for wiring.This Class I Divisions 1 & 2, Class II Division 1 & 2 low profile explosion proof light fixture provides 27,040 lumens of high quality light while only drawing 208 watts. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Since we wanted a flying model it made sense to see if we could build one of the earlier Titan II concept vehicles due to its large fins. To begin we had a scale 3-view drawing from the original Dyna-Soar/Titan II design by the Martin Company. This...

Inspired by the sand drawing tables and the beautiful project SAND watch by Studio AYASKAN, I decided to build my own sand-based clock with a little ancient theme.The sand becomes the watchface as the two marbles draw the time as a line in the...