creasee cs30 3d models

The CS30 stock ships with a mount for the Z endstop that is not moveable. This is a replacement, that will allow you to move it as necessary. ...

The CS30 stock ships with a mount for the Z endstop that is not moveable. ...This is a replacement, that will allow you to move it as necessary.</p> Category: 3D Printer Parts

T-Slot badge reel holder adjusted to tip into the top of the gantry t-slot and remain in place without disassembling the gantry. Simple but effective retractable badge holder - a little bigger and a little heavier than others because I got tired of...

300x300 bed leveling squares

T-Slot badge reel holder adjusted to tip into the top of the gantry t-slot and remain in place without disassembling the gantry. Simple but effective retractable badge holder - a little bigger and a little heavier than others because I got tired...

I have a Creasee CS-30 3D printer and i the duct fan on the right side of extruder needs replacing. There are several Ender-3 duct fans that fits but is too deep down that knocks off prints. ...Decided to design it myself and it works well.

Mount can be printed as oriented with no support. Magnetic Phone stand will require paint-on or tree support. ... To be magnetic, requires 32mm round magnet w/3M double sided disc tape as purchased here: ...

This model was created for more efficient and low-noise cooling of the power supply and printer motherboard. The choice was made in favor of 80x80x25 cooling fans. These fans provide more flow but less noise. You can use 12v and 24v fans, if you have...

This model was created for more efficient and low-noise cooling of the power supply and printer motherboard. The choice was made in favor of 80x80x25 cooling fans. These fans provide more flow but less noise. You can use 12v and 24v fans, if you...

This model was created for more efficient and low-noise cooling of the power supply and printer motherboard. The choice was made in favor of 80x80x25 cooling fans. These fans provide more flow but less noise. You can use 12v and 24v fans, if you...

You can not use the stock filament sensor very well with a BMG Clone extruder on the Creasee CS30. The filament sensor sits about 16mm below the path of the filament in the BMG and it would be a nasty bend in the filament. This is a simple block...

You can not use the stock filament sensor very well with a BMG Clone extruder on the Creasee CS30. The filament sensor sits about 16mm below the path of the filament in the BMG and it would be a nasty bend in the filament.</p> <p>This is a simple...

A simple 10mm spacer to bring the filament sensor up to the same height as a Bigtreetech 3D Printer Upgrade Dual Gear Extruder. ... 10mm tall with 2, 4mm holes spaced 20mm apart.

Works with: https://www.thingiverse.com/thing:5023821 https://www.thingiverse.com/thing:3340432 Use a Zero 2 W and Octoprint, Any other Pi Zero will not run Octoprint with a camera.

Works with: https://www.thingiverse.com/thing:5023821 https://www.thingiverse.com/thing:3340432 Use a Zero 2 W and Octoprint, Any other Pi Zero will not run Octoprint with a camera.

This is a completely 100% reversible mod for the Creasee CS30. The CS30 usually has a Robin Nano v1.3 or a v2.0 board. These boards have a mosfet on them to power, the hotbed, hotend (1 and 2), and fans. The bed itself consumes about 260 watts when...

This is a completely 100% reversible mod for the Creasee CS30. The CS30 usually has a Robin Nano v1.3 or a v2.0 board. These boards have a mosfet on them to power, the hotbed, hotend (1 and 2), and fans. The bed itself consumes about 260 watts...

ALSO, check out Reddit, we have a new unofficial user group r/Creasee3D, with all kinds of cool stuff for the Creasee FDM printers. I just created a custom bed overlay for the Creasee printers. This can be used in both Cura and PrusaSlicer, but I am...

The bed image PNG file can be downloaded here; https://www.mediafire.com/folder/4vxseewitzwpf/CREASEE_BED Then in PrusaSlicer, go to the printer settings tab, then general, then click set for bed shape. Now under Texture, click Load, and select the...

For Creasee SkyWalker 3D Printer. ... Thanks.

For better driver cooling Pet-g

... and extend the top screw slot to fit my printer. ...It was originally for ender 3v2. I have it on my ender 3 pro and creasee CS-30 with microswiss and dragonfly bms hotends and it works great. ... Remixed from https://www.thingiverse.com/thing:5149113

Got a Creasee Skywalker, broke the tip, but had a V6 Volcano hot end and an extra Heat break, great excuse to upgrade a little. Couldn't use the heatsink from the V6 though, eh. Needed a new fan duct. Couldn't find one similar to the old one, so i...

X axis belt tensioner for Creasee CS-30 printer, remixed from: https://www.thingiverse.com/thing:3319649 and https://www.thingiverse.com/thing:4888477 What I did: • Elongated the body, used the 2mm lowered pulley version to ensure belt alignment •...

This is a revision of the print head https://www.thingiverse.com/thing:5172583 for the Creasee CS-30 Consists of: 1. Head mount 2. Fan duct 4010 Creasee CS-30 3. ...Fan duct 4010 Ender 3

required for compensate space after installation a new bi metal throat with e3d nozzle

required foot spacer 25mm --

needed to extend the z stop on my Skywalker because of my new volcano hotend.

Reinforcement of the Bed Capture to Restrict Original Connector Movement. ... I Provide the STL and Pre-Printed GCode Files for the CS10S.

Belt tensioner for rebuild with stock parts.