creality3d ender 5 plus 3d printer

A slightly modified belt tensioner body to fit on the Ender 5 Plus X axis carriage. ... It still requires the nut and thread part of https://www.thingiverse.com/thing:3601830 and this spacer to fit the stock bearings with an M5 bolt:...

Relieving tension on the hot bed cable of Ender 5 Plus requires this modification. No fasteners are required for this setup. Printing without supports is also possible using this method. ... This idea was inspired by BGDog's design, which can be found...

Fixed some slicing errors Simple Cable Management box to hide the cludder on the Ender 5 Plus. Wire pass-through on the back and bottom. ... The lid can be fastend with M3 Bolts Mounting holes to fix the box on the extrusion are provided Walls...

This is a remix of zarify mount https://www.thingiverse.com/thing:4087221 but made to fit an Ender 5 Plus It wont quite clear the hot end but does a good job and doesn't require and additional hardware. ... the cover is friction fit and you may need...

Reworked the bottom to fit a bit better to my Ender 5 plus and made it a bit sturdier. Also resized the holes to fit some brass thread inserts in M3. ...All other needed parts can be loaded from the original source or the remixes.

Use the longer one for both front and back if you have an ender 5 plus. The light bar is long as I wanted as much light possible on my ender 5 plus. If you need less of a strip, just resize it in your slicer. Ender 5 plus has a huge print bed. If...

I removed the little bucket for the SD card and USB drive since I use Klipper and a Raspberry Pi 4 on my Ender 5 Plus. ... Designed this because over time the original I remixed from lost its grip on the 2040 extrusion and started to slide down the...

A simply but useful frame clip for Creality Ender 5 Pro / Plus or similar frames. I used it to tighten cables. Works fine. Very easy to print, functional and doesn´t waste filament. You may stretch the Z-axis to get an wider clip. ...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.

this is a mount to attach the Mosquito hot-end to the Ender 5 plus carriage. ... it will work with my Satsana duct remix found here https://www.thingiverse.com/thing:5120862 Please let me know if you want any tweaks or changes.

I removed the stock cooling fan from the motherboard area of my Ender 5 Plus and replaced it with an 80mm fan. This shroud allows it to sit at the side of the box and uses the existing slots on the side. Vastly improved cooling and much less noise...

This model serves as a dependable wire supporter for the Ender 5 Plus bed, offering a sense of security. ... To assemble this supporter, you'll need to gather the following materials: - Two M3 x 16 bolts and nuts - Two cable ties

... very soft and flexible materials due to the shorter bowden tube. The only additional hardware needed for this modification is longer M4 bolts, at least 15mm long, qty 2. These brackets will only work for an Ender 5 Plus. ... Happy printing!

Ender 5 Plus motherboard fan bracket. Use 4 self-tapping screws to attach the holder. It is possible to use two cheap 12V fans connected in series and connect them directly to the motherboard at the 24V output. ...Use 8 M3x14mm screws to attach the fans...

Simple 5015 fan mount and duct for the Ender 5 Plus.  Compatible with the stock metal shroud & bl-touch mount and does not interfere with stock x-stop or belts. ... Only necessary modification is to remove one of the mounts on the 5015 blower fan...

This is to relocate the stock touch screen on the Ender 5 Plus.I relocated my electronics to a back plate and thus had to make a separate mount for the screen as i removed the original electronics casing.screws together with M3 screws and a single M5...

Camera Holder for Ender 5 Plus I used a D-Link Network Camera DCS‑6500LH It can be rotated arround and up and down from external with an app. Yo do not have to be at home. You need 4x M5 Screw with nuts and 1x M6 to mount the camera itself on the...

More thorough print to cover more of the Ender 5 Plus bed for level testing. Note that the .gcode doesn't prime or skirt so the first disk may not print complete as the filament starts to come out. ... Be careful with where you have your clips for...

My desing of a toolholder for ender 5(plus), it just snaps on the rails i print it in 3 walls and 20% cubic infill takes about 2 and a half hours,has slots for the stock hex keys the wrenches the spatula the sidecutters and some extra slots to hang...

I completely remade his mount from scratch to work with the Ender 5 Plus (though presumably, it would also work with other Ender 5 models) This Thing only comes with the bracket and modified BL touch bracket. You still need one of his cooler fang...

...My design has been put to the test on my Ender 5 Plus printer, which operates seamlessly without any hardware holding it back. To accommodate varying bed thicknesses, users can fine-tune their designs using the scale feature in the slicer software.

This extend your Ender 5 Plus rubber feets by 35mm. (I need this for my own silent cooling solution, maybe I will show you later). Maybe you like this too to add more airflow to the Z stepper motors. You need 4mm brass inlays, so you can reuse the...

This piece supports the wire going to the hot end on the Creality Ender 5 Plus. The V4 file is designed to connect to the printer with two M3x10 machine screws and two M3 T-nuts, while the tube connects with a zip tie or twist tie. This piece...

I needed led strip holder for my Ender printer.

So startete ich Freecad und passte die Vorlage an meine Bedürfnisse an. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Yes Supports: Yes Resolution: .2 mm Infill: 15% Filament: Material4Print PETG black Category: 3D Printer...

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

If your printer uses the same carriage plate that the ender 5 plus does then this should work for you too. This uses the stock BLtouch mount and you can use the stock 40mm fan but if you want the cooling fan you'll need a 5015 blower (I have not done...

A convenient yet essential covering for stepper motors on Ender 5 Plus printers safeguards against unwanted debris like dust and crumbs that could cause motor malfunctions down the line. If printed in a striking color, it adds an attractive touch. 2....

A simple yet useful cover for stepper motor on Ender 5 Plus. It will protect your motor interior from unwanted mess (dust, crumbs, etc.) which could potentially stop it from running smoothly it in the future. If printed in a nice color it looks...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...