creality sprite extruder review 3d models

Work In ProgressVersion 0.98 should be good to go, but is untested I should have this version tested and instructions soon.Version 0.9 only has one problem The fan mount needs about 1mm to be trimmed off with a knife for it to work right now.Basic...

this eats up some x axis space, be warned.

Обдув под SPAP для экструдера Спрайт от Креалити по модели Дмитрия Соркина с сайта K3D.Для апгрейда принтера Эндер 3.

The Nema Extruder Bracket provides effortless access to the Nema, eliminating the need for a filament guide. It also enables an extruder to be partially assembled before fitting it to the printer. After several months of testing, I have used it daily...

This component is specifically designed to be compatible with Creality's Ender 3 and 5 three-dimensional printers.

My firmware config files for my printers marlin build which is an ender 3 max frame with a BTT SKR mini E3 V3 mainboard and a creality sprite pro extruder kit including CR/BL Touch and working stock filament runout sensor. ...I've included the built...

Sprite/ender 3 s1 extruder flat cable holder for ender v2

Extruder fan adapted for SPIDER HOTEND on a cr10s pro, direct ectruder with layer fan.

After relocating the extruder I wanted to plug the hole that remained.

The DIY Extruder Arm Cover gives new life to your existing soft plastic extruder, allowing you to continue printing without interruption until your upgraded replacement arrives safely in your hands.

Inspired by the Yoda Ender 3 Extruder knob, I desired one to guarantee my prints would all finish perfectly okay! It's absurd, I acknowledge, but it brings me joy. ... Gratitude goes out to the original artists for creating the extruder knob and the OK...

I liked Cornely Cool's design, but found the cable guide interfered with my extruder release handle. Also wanted my reverse bowden tube to go all the way to the extruder. The "tear drop" tube hole was a Great suggestion from Makers Muse, that...

You need to mount the frontplate on the original hotend carrier for using a BMG or BMG Clone as a direct extruder with the original hotend. ...Four pieces of 5mm longer M3 screws are required for the extruder, which I printed out in PETG.

Support is available for installing a stepper motor in a car and an Ender 4, with the understanding that it can also be applied to other Creality printers. ...The open file is in need of improvement and was created using SolidWorks 2018 as a model.

this is a remix but i can't find the original, sorry. ...direct extruder mount for smart filament runout sensor from bigtree tech. holds tight works well. ...i used tree support with cura

My personal printers are the Geeetech A30 (2.80 mm) and Creality CR10 S4 (2.50mm). It's a good idea to measure thickness before printing out the model, and you can adjust the .stl file if necessary. ... The bearing I used is 6206-c-2z (35.00x11.00 for...

[13 Oct 2023 update] some one PMed and said the 3mf is not working on some slicer, uploaded a stl version as well.There is an annoying issue with K1, that you can't print PLA or other lower temp materials with lid on, otherwise it might either under...

I was fed up with fiddling around with spacers and similar components so I lost the spring for my extruder, therefore I decided to utilize a leftover M5 bolt from the Ender 3 kit along with all of the hardware present in the stock extruder arm. P.S....

You'll need to gather the following materials: - PTFE tubes / fittings - M3x30 + M3x15/20 + 2x M3 nuts and some washers, some screws can be reused - 1 Spring that can be reused from the original extruder - 1 Bearing (11mm) that also can be reused If...

I desperately needed a bracket for my hotend cable after swapping out the extruder on my CR10S Pro dual gear printer (Amazon's Leoway model). ...With lightning speed, I whipped up a quick design using Google Sketchup, drawing inspiration from Namemogan...

I relocated the extruder to avoid having to shift my head back and forth while swapping colors. ... The length of the screws needed depends on your drive mechanism, so make sure to get ones that are between 2mm and 4mm longer than usual.

I've been using PETG successfully in combination with TPU, PETG, and PLA, thanks to the reliable performance of my duel gear extruder arm. ...This has eliminated the need for me to constantly adjust my esteps when switching between different filaments.

I used the idea from Kevin Wong, however I designed it from sketch, but credit is to Him.Printed from PLA, a little support needed due to this part wraps around extruder and makes it more stable.

Place this over the bolts near the extruder tube (above the filament roll) so it doesn't catch or abrade. Bolts are 2cm apart, use a cut sliver of 3M Command strip (for example) to attach to frame over the bolts. This object was made in...

The original Ender 3 extruder breaks the plastic because the axis puts pressure on one point. In this modification, there is support above and below, making it much more durable. ... Personally, I printed it in PLA and haven't had any issues since,...

Visualize the rotation of your printer's extruder with clarity.\n\nMaterial used is PLA wood.\n\nThe nozzle diameter is set to 0.4mm.\n\nLayer thickness is precisely 0.1mm.\n\nDimensions are carefully measured at L25mm x W15mm x H7mm, featuring a...

I redesigned the flexi filament extruder with a sturdy cable management system. A sleek ring was integrated into the existing project, providing secure protection for the hotend cables. ...Using Tinkercad's powerful fusion tools, I combined the ring...

I adjusted the overall dimensions of the design to fit perfectly around the Ender 3 Pro extruder pin. This means you can print it at full scale and be ready to go straight away. ...Simply flip it upside down like in the STL file, and you'll avoid...

EDIT: Added V2 with PTFE tube zip-tie cinch and more room for extruder arm movement A remix of the original https://www.thingiverse.com/thing:4468446/remixes It is a perfect fit. I love the idea of having my spool of filament on the side and plastic...

This print is a simple and efficient way to reposition the extruder motor, making it easy to feed filaments from the back. This approach eliminates the need for additional prints that guide the filament when you already have your spool holder set up...