creality ender 5 plus upgrades 3d models

My Ender 5 Plus was extremely loud, so I changed all its fans. The loud one at the nozzle was swapped with a 40x20mm Cooltek one (very nice result) and so it did not fit into the normal metal duct. This one is designed in the same style, only...

DE: Ich habe noch eine vernünftige Halterung für meinen Ender 5 Plus gesucht, in der ich den Bildschirm von BIGTREETECH unterbringen kann ohne dass es zu aufwändig wird oder gar eine extra Box an einer Seite steht. Ich finde das Design vom Ender 5...

DO NOT OVERTIGHTEN Tested Print Settings Using 3D Fillies PLA+ Glass_bed_clamp_v1 Tested with cura standard quality 0.2mm with ender 5 plus Print Verticle with Brim support for extra strength. Tap maybe needed if unable to get threads overhang...

I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. I made a remix of a custom creality X axis bracket. This bracket...

Hello All out there , Here's a proposition for a Z axis lead screw Guide for ender 5 plus printer. Drawing is extra simple . See following Videos : https://youtu.be/0vTzRNAVvf0 https://youtu.be/bXGqCE6AxoA You will need : 4 M4*10 screws...

NOTES: - In case you would change your mind and you would like to go back for the default blue one simply download the second .zip file " Creality_7.32_Screen.zip" and use these files. These clean files are the creality original. Then start the...

NOTES: - In case you would change your mind and you would like to go back for the default blue one simply download the second .zip file " Creality_7.32_Screen.zip" and use these files. These clean files are the creality original. Then start the...

This is the best laser module mount I have had so far for my Ender 3 S1 Plus. No vibrations, no wobbling, no artifacts. Prints in less than 2 hours, fits perfectly and the gantry needs to be much lower than if the laser was mounted with the original...

It holds all the tools that came with both the Ender 5 and the Ender 5 Plus, plus maybe a few others. ... The filament I use is Hatchbox, you can check them out here: https://amzn.to/38XzBLq If you're using something different, you might want to adjust...

I used the 2020 frame clip-on of the “2020 Extrusion Webcam Mount [No Hardware] Logitech C270” found on thingiverse (https://www.thingiverse.com/thing:4636337) and the cable tree holder of the “Ender 5 / Ender 5 Plus Print Head Cable Strain Relief...

If you own an Ender 5 Plus and install the Printermods MDD 1.2 direct drive plate, you'll discover that the stock metal BLTouch mounting plate won't fit properly. None of the pre-printed BLTouch mounts match, so I chose to modify the metal one...

After purchasing Exoslides for my Ender 5 Plus I found that the H2 adapter wasn't compatible with the exoslide. Installing this requires disassembling the H2 to screw the center section of the extruder to the adapter. Next step is to connect the...

Mount for the Adafruit ADXL343 Accelerometer that works on a Ender 5 Plus with BLTouch. ... **Parts Required** - Adafruit ADXL343 [on Amazon](https://www.amazon.com/gp/product/B07PN6ZBJF/) - 2x M3*20mm Hex Socket Head Cap Screws and Nuts [on...

My ender 5 plus factory spec out the box has this additional dampening bracket. Which needs slightly more space for the cover to fit properly. Test prints fit perfectly. Use the same fastening / fixtures listed in the original. ...Worked a treat.

Ender 5 Plus bracket designed specifically for SKR 1.3 and 1.4 motherboards, optimized to provide easy access to the SD card slot and USB port. To assemble this bracket, you'll need to locate and carefully cut a precise slot and hole on one side of...

# WHAT THIS 3D PRINT IS NEEDED FOR AND WHY IT WAS DEVELOPED: This 3D print resulted from the fact that after a while the cable guide of my Ender 5 plus kept bending towards the heatbed due to the weight. After a while, the cable guide was so deep...

This is a remix of the switch mount for the 3DChameleon MK2 that fits in the rear left corner of the Ender 5 Plus sitting ontop of the corner bracket allowing for you to use the Y axis to trigger the switch. The switch ends up triggering at the same...

This is a Cable Holder for the Ender 5 Plus with linear rails and the Micro Swiss Direct Drive I use this cable chains 20x10mm: https://www.aliexpress.com/item/32999589537.html?spm=a2g0s.9042311.0.0.27424c4dZDh4ri I use the cable chain trays from...

Use the same information as the original file, this just adds a slot to store one additional SD card on the side From original: So I made this thing for my Ender 5 Plus +, you need a couple of M3 or M4 x 10 bolts and T-nuts to attach it. I also put a...

I'm using it on the new SKR 3 board for the Ender 5 Plus, but the SKR 3 mounting points are the same as the SKR 2, and I think the SKR 1.x boards too. I printed this in ABS, but PLA or other material should work fine. It's designed to be a press...

See the original creator here: https://www.printables.com/model/436006-ender-5-plus-with-microswiss-ng-cable-chain The original creator made these for a 10x15 cable chain that was purchased from Amazon. He used the closed version of the chain,...

No Support needed, 4 brackets needed for Ender 5-Plus I made this adapter to quickly fix the Z-Rod height on my Ender 5-Plus while using the Mini-Me Mosquito mount to avoid collisions. The BL Touch needs to be spaced down about 15mm to be used in...

To attach the raiser to the frame of the Ender 5 Plus you can simply use M3, M4 or M5 T-Nuts. You can get them here: ...

Removed Creality Logo

... This keeps the extension arms firmly in place on the front 20x40 extrusion. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: NoResolution: .2 Infill: 25% Filament: Duramic3D PLA+ White Category: 3D Printer Accessories

... need it. ...I have not printed this yet but please tell me if it needs to be fixed. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: YesResolution: 200 Infill: 15 Filament: Ziro PLA Black Category: 3D Printer Accessories

This print is for side mounted light bars for the Ender 5 Plus. I wanted them on the sides so they were out of my way and have two light bars for better lighting. The brackets are RH / LH so the X axis motor on the gantry is the RH bracket. I also...

This fan shroud is designed to specifically fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans and BL Touch mount while providing clearance to the linear rail mounts. This...

This is a small modification to Boont's Ender 5/5+ Mod to make it compatible with the Eva v2.4 system.

Rear belt clip video installed on an Ender 5 Plus: https://www.youtube.com/watch?v=5KwS48xxb3w Front belt clip video installed on an Ender 5: https://www.youtube.com/watch?v=1vp6IQ8vMQI UPDATE 02/24/2020: The Hemera Linear Rail mount has been...