creality ender 5 plus upgrades 3d models

Ender 5 Plus BTT smart filament sensor mount, this goes in the place of the stock sensor and uses the same M4 bolts and T nuts. ...Wire management for the hot end wiring to bring the wires off of the back extrusion to make way for top enclosure.

SKR PRO board holder for Ender 5 Plus printer.It does not require mechanical modifications, the cables to the drivers can be stored under the board.Use the original holes and screws to attach the bracket. ...Screw the board to the holder with a 3mm...

The Ender 5 plus's location on this design smacks the Bl touch on the Z rails when homing, moving it out of the way but still requiring offset changes to avoid hitting the left-hand side Z rods. ...I adjusted these offsets in the starting gcode within...

This is for the Ender 5 Plus with linear rails with a Micro Swiss Direct Extruder mounted. To mount the Switch you must thrill 2x M3 screw threads. I hope this Thing is useful for you UPDATE: V2 now available I had Problems with the...

I did a remix of the Ender 5 plus hemera mount https://www.thingiverse.com/thing:4026886. but found that the nozzle was sitting higher then the wheel on the rail making it impossible to level. so I lowered the mount holes by 3mm and that gave me...

This display holder was specifically designed for a Big TreeTech TFT24 V1.1, allowing it to be mounted in an Ender 5 plus. ...To install the new holder, removal of the old display is necessary so it can be easily seated.

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. ... You have to ad support to the holder but not to...

This gasket has the screw holes oversized and spaced to fit the stand-offs in the Ender 5 Plus's case. ... I noticed a slight whistle and visible gap between my fan and the case; it probably would not be an issue for most people but my printer is in...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ...Will Need: 10mm Magnets 3mm...

This mount seamlessly integrates both the BLTouch and filament run out sensor that come standard with the Ender 5 Plus. It attaches securely to the stock metal mounting bracket, so I'm confident it will be compatible with every printer in the Ender...

Custom electronics enclosure for Ender 5 Plus printer suitable for BigTreeTech GTRv1.0 and M5 boards. Is designed to take standard Meanwell power supply, Creality heated bed MOSFET, Creality standard touchscreen (others will also fit), BigTreeTech...

I created this simple direct drive out of frustration of the substandard quality from my Creality Ender 5 plus. This is to be used in conjunction with the new hot end, the “Phaetus Dragon ST. I made it so it fits easily using most of the Creality...

This was made specifically for the Ender 5 plus with the extruder gear that DOES NOT have a set screw. The original gear comes off relatively easy if you get some WD-40 into it, let it sit, the put the motor in a vice and use a prybar (gently) to...

A few changes were needed to get this to fit on my Ender 5 Plus. I went with spacers to adjust the Z. On the Micro Swiss Direct drive there was no need for the cut out area so I removed it to increase strength. This will print with no supports .

An all in one BIQU H2 Extruder mount for an Ender 5 or five plus, X and Y end stop mounts are from from a linear rail upgrade kit. I've uploaded a couple remixes, of the Y enstop I think the V2 should be about right as the V1 was too Small Nozzle was...

This contains two lengths of bracket for moving the standard spool holder bracket 25 mm or 50 mm to the rear of the Ender 5 Plus. This allows the use of the large replacement spool holders such as the design this is a partial-remix of.The newly...

======== This mount allows the use of the direct drive quick change toolhead by VORON Designs called the Afterburner on a Creality Ender 5/Pro/Plus. The Afterburner is the latest toolhead from Voron and offers the flexibility to use three different...

Its a remix for the Ender 5 Plus... the original version is for the Ender 5... it is also aligned based on the stock hot end... it may work with other hot ends as well,.however mine is the stock and this works great. I printed it in PETG at 100%...

To power this LED strip holder, I employed the Ender 5 Plus's built-in power supply, supplemented by a simple dimmer to achieve the desired brightness levels. ...For added versatility, I also created an enhanced version of this design with increased...

I made this tool carriage the same length as the stock Ender 5 Plus's tool carriage, with similar 'hooks' to continue to use the stock belt with it's crimps. STEP file is include if folk want to adapt it to their own machine. ...Unfortunately,...

I successfully installed it on my Ender 5 Plus, but it should also work seamlessly on the CR 10S PRO V1 or V2. The same bolts are utilized for this purpose. ...If you want to achieve even greater stability, I highly recommend using two metal inserts...

Purchased a Winsinn Dual Gear Extruder for my Ender 5 Plus, however the filament coming out of the filament runout sensor no longer lines up properly with the filament hole into the extruder. This mount will line the filament holes up properly. ...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. ...After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints.</p> <p>Will Need:<br/> 10mm...

This is a small modification to allow for the clearance for the BTT SKR E3 Turbo in the Ender 5 Plus. The hardware is the same for mounting, as mentioned you should use inserts or nuts with the mounting bolts. This also assumes you have made...

This is a mount to allow you to put a BTT TFT35 v3.0.1 screen in the Ender 5 Plus. It is slightly recessed so that you don't have to cut a notch in the opening for the dial. Have not tested a print yet. Simply printed the original and noticed some...

I did a remix of the Ender 5 plus hemera mount https://www.thingiverse.com/thing:4026886. but found that the nozzle was sitting higher then the wheel on the rail making it impossible to level. so I lowered the mount holes by 3mm and that gave me...

Designed to replace the stock Filament Sensor that ships with the Ender 5 Plus. Should line up perfect with the existing hole pattern under the extruder. I used a brim but supports shouldnt be needed. 10-15% infill should be fine. If you plan on...

I created something quick to fit on the stock Ender 5 Plus hot end mount. There is an option for a pass through for the Bowden tube. Happy to provide more details if folks like this design End Caps for Open V-Slot 2020 with Open Hardware logo. ...

Made a mashup of my previous remix for the ender 5 plus and the mini satsana for the ender 3 (Ill credit when i can figure out which one) You will need to add custom supports under the two risen areas for the BLTouch mount. otherwise no other...