creality ender 3v2 3d models

It is running Marlin 1.1.9 and has an SN4 induction sensor, an E3Dv6 with a removable magnetic build plate (cut down from an Ender replacement). Marlin source changes are now in the download. (some settings are just because I'm recycling an old ANET...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

I managed to print it with regular CR10 on my slightly modded Ender 3 V2, but I had to temporarily remove part cooling fan, bed leveling sensor and even silicone sock, clearances are that tight for CR10. It's not possible to slice a print like this...

Wer am Ender die meisten Punkte hat, der hat das Spiel gewonnen. Wer sich für das komplette Set von Redline Filament entschieden hat, der muß seinen Arduino nicht mit dem Sketch flashen. https://redline-filament.com/products/chaos-run-paket Alle...

Wer am Ender die meisten Punkte hat, der hat das Spiel gewonnen. Wer sich für das komplette Set von Redline Filament entschieden hat, der muß seinen Arduino nicht mit dem Sketch flashen. https://redline-filament.com/products/chaos-run-paket Alle...

 It is an upgrade on top of the AM8 upgrade (https://www.thingiverse.com/thing:2263216)  by pheneeny.The parts will probably also work with an ender e3 and other bedslingers which have an aluminium extrusion frame, but might need some...

They should fit on most printers, though check your firmware limits first if you're using a printer like an Ender 3 which may be artificially limited to 210x210 if running stock firmware.Basic Base is 180x180x52mm with a 24mm deep hole for the...

 Too much extrusion will get you tiny bumps around your print; too little can make it too fragile and prone to cracking between layers.If you're getting weirdly evenly spaced bumps on the outside, especially if you're on a more basic machine like an...

Most don't need supports, the "Top" piece printed without supports on my ender 3, but the overhang angle was a bit steep, so I probably should have used supports on that. It came out a little wavy on the angled parts. The "Right Side" might need...

Wer am Ender die meisten Punkte hat, der hat das Spiel gewonnen. --- Wer sich für das komplette Set von Redline Filament entschieden hat, der muß seinen Arduino nicht mit dem Sketch flashen. ...

For the spit roast turning thing I used a nozzle cleaner wire that comes with an Ender 3 and stuck it through the holes in the roaster, bent it, and cut it to size using flush cutters. Once I was happy with this, I put some putty around the wire to...

......(I put “simple” in quotes because designing this thing and perfecting it has been anything but simple.) My goal was to create a ball clock that could be 3d printed relatively easily on an Ender 3 class 3d printer and assembled without too much fuss.

......(I put “simple” in quotes because designing this thing and perfecting it has been anything but simple.) My goal was to create a ball clock that could be 3d printed relatively easily on an Ender 3 class 3d printer and assembled without too much fuss.

https://www.thingiverse.com/thing:3391502 for DF95/DF65 https://www.thingiverse.com/thing:2139038 for DF65/RG-65 https://www.thingiverse.com/thing:3250906 for IOM Also, many thanks to David Jennings himself for sparking the fires of so much creation...

&nbsp;Ender 3 springs are fine, although you'll have to compress the secondary spring a bit. If you have to be specific:<br><br>The springs should simply have an ID of more than 0.21" and a free length of 15mm+. I believe <a...

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...